User manual SONY SU-WL500 INSTALLATION GUIDE

[. . . ] Be sure to read this instruction manual thoroughly to do the installation work safely. Sony is not liable for any damages or injury caused by mishandling or improper installation. Please give this manual to the customer after installation. LCD Color TV This Wall-Mount Bracket is designed for use with the specified products above. [. . . ] · If you have routed 300-ohm feeder cables behind the wall, we recommend that you change them to 75-ohm coaxial cables. If it is necessary to continue to use 300-ohm feeder cables, be sure there is sufficient space available between the TV and the feeder cables behind the wall before installing. Consult your licensed contractor regarding an appropriate location (free from radio noise, etc. ) before installing. Be sure to use the supplied screws and attachment parts properly following the instructions given in this instruction manual. If you use substitute items, the TV may fall and cause bodily injury to someone or damage to the TV. Be sure to assemble the bracket properly following the instructed procedure explained in this instruction manual. If any of the screws are loose or fall out, the TV may fall and cause bodily injury to someone or damage to the TV. 4 (GB) Be sure to tighten the screws securely in the designated position. If you fail to do so, the TV may fall and cause bodily injury to someone or damage to the TV. Before installation If you intend to install a TV that is not specified on page 2, be sure to refer to the leaflet "Installing the WallMount Bracket" supplied with your TV. Be careful not to subject the TV to shock during installation. If the TV is exposed to shock, it may fall or break apart. This may cause injury. Be sure to install the TV on a wall that is both perpendicular and flat. If you fail to do so, the TV may fall and cause injury. Step 1: Checking the parts required for the installation 1 Prepare four or more 8 mm diameter or equivalent screws (not supplied) and a screwdriver. Select screws suitable for the material of the wall. Unpack the carton and check to see that all the following items are included. After proper installation of the TV, secure the cables properly. If people or objects get tangled with cables, this may result in injury or damage to the TV. Do not allow the AC power cord or the connecting cable to be pinched. If the AC power cord or the connecting cable is pinched between the unit and the wall or is bent or twisted by force, the internal conductors may become exposed and cause a short circuit or an electrical break. This may cause a fire or an electric shock. 2 Be careful not to hurt your hands or fingers during the installation. Be careful not to hurt your hands or fingers when installing the Wall-Mount Bracket or the TV. Base Bracket (2) The screws needed to secure the Wall-Mount Bracket to the wall are not supplied. Use the appropriate screws for the wall material and structure when mounting the Wall-Mount Bracket. Mounting Hook (2) Screw (+PSW6 × 16) (4) Screw (+BVST4 × 12) (6) Hexagon wrench (1) 5 (GB) Step 2: Deciding on the installation location 1 Referring to the TV installation dimensions table on page 12, decide on the installation location. Allow for suitable clearance between the TV and the ceiling and protruding parts of the wall as shown below. Unit: mm 2 Referring to the Wall mounting dimensions diagram on page 13, determine the positions of the screws for installing the Base Bracket. WARNING The wall that the TV will be mounted on should be able to support a weight of at least four times that of the TV (Refer to your TV's instructions for its weight. ). Determine the strength of the wall the TV will be mounted on. Reinforce the wall sufficiently, if necessary. 100 300 100 Never install the TV set as shown below: Air circulation is blocked. 100 Wall Note If you intend to route the cables in the wall, make a hole in the wall to insert the cables before beginning the installation. 6 (GB) Step 3: Installing the Base Bracket on the wall 1 Secure the Base Bracket to the wall using four or more 8 mm diameter or equivalent screws (not supplied). 1 Determine the screw holes (d, h) for attaching the Mounting Hook to the Base Bracket. Then attach them securely using the supplied screws (+BVST4 × 12). Screw (+BVST4 × 12) 2 Secure the Base Bracket and the Mounting Hook on the wall using the four or more 8 mm diameter or equivalent screws (not supplied). Select four screw holes with the z mark shown in the diagram below and tighten the screws securely so that they will not become loose. Align the unit so that it is level. d g h Base Bracket 3 Remove the screws which were attached in procedure 1 and detach the Mounting Hook from the Base Bracket. Base Bracket Mounting Hook CAUTION Be careful not to drop the Mounting Hook when removing the screws from the Mounting Hook. WARNING · The screws required for this procedure are not supplied. Select screws suitable for the material and structure of the wall. · If the Base Bracket cannot be attached securely enough, use additional screws. [. . . ] · Be careful not to hurt your hands or fingers when removing the TV. WARNING Be sure that two or more persons hold the TV when carrying it. When removing the TV To Sony Dealers Specifications Unit: mm Weight: 4. 7 kg 1 2 Unplug the AC power cord from the wall outlet. Remove the two screws which secure the TV and the Base Bracket. (Refer to 3 of Step 5 on page 10 for the screw positions. ) 525 60 73 Design and specifications are subject to change without notice. 450 11 (GB) TV installation dimensions table The table below shows the dimensions of the TV that is mounted on this product. [. . . ]