User manual SONY SVP1110

[. . . ] · Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. · Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only. · Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers. [. . . ] · If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. · Do not use a new battery with an old one. · Do not use different types of batteries. Inserting the batteries Insert two size AA (R6) batteries by matching the + and ­ on the batteries to the diagram inside the battery compartment. Using the remote commander You can use this remote commander to operate this Video Cassette Player (VCP) and a Sony TV. Buttons on the remote commander marked with a dot (·) can be used to operate your Sony TV. Remote sensor TV / VIDEO 6 1 2 3 To operate Set TV / VIDEO to the VCP a Sony TV VIDEO and point at the remote sensor on the VCP TV and point at the remote sensor on the TV Controlling other TVs with the remote commander Tips · If you set your TV's code number correctly while the TV is turned on, the TV turns off automatically. · If you set the code number 20 for your TV, you can use almost all the buttons marked with a dot (·), and the TV/CAPTION/TEX, CAPTION CH1/CH2, RESET and Q. VIEW buttons on the remote commander. The remote commander is preprogramed to control nonSony TVs. If your TV is listed in the table on the next page, set the appropriate manufacturer's code number. 1 2 Set TV / VIDEO at the top of the remote commander to TV . Hold POWER down, and enter your TV's code number(s) using the number buttons. Then release POWER. 4 Now you can use the POWER, VOL +/­, CH +/­, and TV/ VTR buttons to control your TV. You can also use the buttons marked with a dot (·) to control a Sony TV. To control the VCP, reset TV / VIDEO to VIDEO . SONY SVP-DC1 (E) 3-194-445-02 (3) Code numbers of controllable TVs; If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. Notes · If the TV uses a different remote control system from the one programmed to work with the VCR, you cannot control your TV with the remote commander. ­ Bands appear on the top or bottom while pausing. · The CASSETTE indicator on the front of the Video Cassette Player lights in green whenever the cassette is inserted even when the power is off. T-160 T-120 T-60 T-30 2 hrs. 30 min. Notes · When the pause mode lasts for more than about five minutes, the Video Cassette Player will automatically enter the stop mode. In pause mode, the P PAUSE button blinks. · When the stop mode lasts for more than about five minutes, the VCP will automatically turn off. · The playback sound is muted during various speed playback modes except for normal speed playback. · Noise appears on the screen while pausing as the VCP is two-head type. Especially, the pause mode picture of the tape recorded in the SP mode is not stable. This is not a malfunction of this VCP. 8 SONY SVP-DC1 (E) 3-194-445-02 (3) Repeat play You can play the recorded portion of a tape repeatedly. 1 p STOP AUTO OFF Set the AUTO switch to a. 2 Insert the recorded tape. The Video Cassette Player starts playing. After playing the recorded portion, the VCP rewinds the tape to the beginning and plays the same recorded portion repeatedly. To stop playing Press p STOP. 6 1 4 7 2 5 8 0 3 6 9 Conditions of the tape for repeat play To use the repeat play function, the tape must meet the following conditions: · The blank portion at the beginning of a tape must be less than 25 seconds. [. . . ] To resume automatic tracking adjustments, press TRACKING + and ­ simultaneously. TRACKING +/­ Notes · The Video Cassette Player may not reproduce a good quality picture if the tape or the recording is in poor condition. · When you play a tape recorded with the copyguard system, you may occasionally see distortion in the upper part of the picture. in EP mode (with T120 tape) Fast-foward and rewind time Approx. (with T-120 tape) General Power requirements 12 V DC (10 V­16 V DC) Power consumption 13 W Operating temperature 5°C to 40°C (41°F to 104°F) Storage temperature ­ 20°C to 60°C (­4°F to 140°F) Dimensions Approx. [. . . ]