User manual SONY TA-N90ES

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna (aerial). ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] · If you play a disc for which Parental Control is set, this function does not work. Resuming playback from the point where you stopped the disc (Resume Play) Tip To play from the beginning of the disc, press x twice, then press H. (DVD VIDEO, DVD-VR, VIDEO CD, Super Audio CD, CD, DATA CD, DATA DVD only) When you stop the disc, the system remembers the point where you pressed x and you can start playback from the point you stopped the disc. Searching for a particular point or a scene on a disc Searching for a particular point on a disc (Scan, Slow-motion Play, Freeze Frame) 1 While playing a disc, press x to stop playback. "Resume" appears in the front panel display. If "Resume" does not appear, Resume Play is not available. (DVD VIDEO, DVD-VR, VIDEO CD, Super Audio CD, CD, DATA CD, DATA DVD only) Note Depending on the DVD/VIDEO CD, you may not be able to do some of the operations described. 2 Press H. The system starts playback from the point where you stopped the disc in step 1. To enjoy a disc that is played before by resume playback (Multi-disc Resume) (DVD VIDEO, VIDEO CD only) This system stores the point where you stopped the disc for up to 40 discs and resumes playback the next time you insert the same disc. If you store a resume playback point for the 41st disc, the resume playback point for the first disc is deleted. To activate this function, set [MULTI-DISC RESUME] in [CUSTOM SETUP] to [ON]. For details, see "[MULTI-DISC RESUME] (DVD VIDEO/VIDEO CD only)" (page 65). Notes · If [MULTI-DISC RESUME] in [CUSTOM SETUP] is set to [OFF] (page 65), the resume point is cleared when you change the input. · The point where you stopped playing may be cleared when: ­ you change the play mode. ­ you change or reset the settings on the Setup Display. ­ you disconnect the AC power cord (mains lead) for a long period of time. Locating a point quickly by playing a disc in fast forward or fast reverse (Scan) (except for JPEG) Press m or M while playing a disc. When you find the point you want, press H to return to normal speed. Each time you press m or M during scan, the playback speed changes. With each press the indication changes as shown below. Press M/m repeatedly until "Memory?" appears in the front panel display. Press (ENTER). A preset number appears in the front panel display. TUNED ST 37 US Using the Monitor Menu Note You cannot use the monitor menus while receiving the FM signals. Navigating through menus MONITOR Using Inputs in MENU The Inputs feature lets you select the inputs connected to your system. You can also assign a label using Label Video Inputs in the Setup settings (see page 45). 1 Select [Inputs] from the MENU control panel and press (OK). The Inputs list appears. Make your selection. Inputs INPUT </M/m/, MENU O RETURN (OK) Return Video 1 Video 2 Video 3 DVD Video 5 Video 6 Video 1 Video 2 Video 3 DVD Video 5 Video 6 Select: Set: Exit: MENU 1 2 3 Press MONITOR to switch the remote FUNCTION to MONITOR. Press INPUT repeatedly to select the desired input (other than FM). Press MENU. MENU display appears. 2 Press M/m to select the desired input and press (OK). Using Settings in MENU The Settings feature lets you enter to the settings screen where most of advanced settings and adjustments are performed. MENU Inputs Settings Overview of the Settings menus The following options are available in each menu. For details on navigating through menus, see page 39. Also, see page in parentheses for details of each menu. 1 Select from connected equipment Select: Set: Exit: MENU Select [Settings] from the MENU control panel and press (OK). [Settings] display appears. 2 1 2 3 4 Press M/m to select the options. Video Picture Mode: Vivid Reset: Picture: Max Brightness: 40 Color: 60 Hue: 0 Sharpness: 18 Color Temp. : Cool CineMotion: Off Black Corrector: On NR: Low Backlight: Max Select: Back: Set: Exit: MENU 4 Press M/m to select the item. · [Inputs]: Selects equipment that is connected to the system. You can assign a label to your equipment or skip unused inputs conveniently. · [Settings]: Adjusts the [Video], [Screen], [Parent], or [Setup] settings. For details, see page 38. Video 1 5 Press </M/m/, to change/set the setting, then press (OK). To exit the menu, press MENU. [. . . ] During stop, press s on the system or x on the remote and then start playback (page 34). · The title, DVD or PBC menu automatically appears on the monitor screen. · The DVD features an auto playback function. · Some discs may contain an auto pause signal. [. . . ]