User manual SONY TC-M4TR

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] After completing the adjustment, stop type II tape playing the program source, then continue the For type IV tape procedure from Step 5. dB ­ ­30 ­20 ­10 ­4 0 +4 +8 * HX Pro headroom extension originated by Bang & Olufsen and manufactured under license from Dolby Laboratories Licensing Corporation. "DOLBY", the double-D symbol a and "HX PRO" are trademarks of Dolby Laboratories Licensing Corporation. 7 Advanced Recording Operations Adjusting the Recording Level Automatically (Auto Rec Level) The Auto Rec Level function automatically measures the peak signal level and adjusts the recording level accordingly. PAUSE P REC r · AUTO DIRECTION D a RELAY DOLBY NR OFF B C 3 SYNCHRO DUBBING AB HIGH/NORMAL START(DECK B P) DECK A COUNTER RESET DECK B PAUSE REC MUTE REC FADER ARL 1 0 10 9 2 REC LEVEL 4 5 6 7 8 z You should adjust the recording level manually with REC LEVEL in the following cases: --The recording level cannot be adjusted properly due to excessive noise in the program source. --The program source level is too low and the recording level does not increase. During a quiet passage in a program source such as classical music, the recording level may not increase for some time. If a high sound level is expected later on in the track, play that portion first so that the right adjustment can be obtained. --The recording level does not decrease for a long time. The Auto Rec Level function may not work properly when you try to record sound produced by a graphic equalizer that has extremely high-level signals. P 0 p § R ) ª r 0 POWER ) ª · § PHONES p · z 1 Follow Steps 1 to 3 of "Recording on a Tape" on page 6. Make sure that record-protect tabs on the cassette have not been removed. The AUTO indicator flashes and the deck automatically adjusts the recording level. The AUTO indicator lights up continuously after the recording level has been adjusted. Recording starts. To record with the optimum recording level · To prevent changes in the recording level after recording starts, press REC r while playing the highest sound level portion of the program source to be recorded. · Should any solid object or liquid fall into the cabinet, unplug the tape deck and have it checked by qualified personnel before operating it any further. Notes on Cassette Tapes To protect a recording on side A or B Break out the respective tab. Side A On power sources · Before operating the tape deck, check that the operating voltage of the tape deck is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the tape deck. · If you are not going to use the tape deck for a long time, be sure to disconnect the tape deck from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord. · AC power cord must be changed only at the qualified service shop. Tab for side B Tab for side A To record on a tape with a missing record-protect tab Cover the respective tab hole with adhesive tape. On operation · Because of a safety mechanism, the function buttons will not operate if the cassette holder is not completely closed, if there is no cassette in the cassette holder, or if a cassette has been incorrectly inserted into the cassette holder. · Be sure to stop the tape before turning off the tape deck. When you are using a type II or type IV tape, be careful not to cover the detector slots that the deck uses to determine the tape type. Type II Type IV On placement · Place the tape deck in a location with adequate ventilation to prevent heat build-up in the tape deck. · Do not place the tape deck: -- on a soft surface such as a rug that might block the ventilation holes on the bottom. -- in a place subject to direct sunlight. [. . . ] Replace the front cover. 2 3 12 Additional Information Troubleshooting If you've experienced any of the following difficulties while using the tape deck, use this troubleshooting guide to help you remedy the problem. Should the problem persist, consult your nearest Sony dealer. The function buttons do not work. / The tape deck has been just turned on and does not operate for about 3 seconds. / Check that the cassette is inserted correctly and the cassette holder is closed completely. There is excessively loud tape transport noise during fast-forwarding or rewinding. / This noise is caused by the cassette and is not a mechanical problem. § does not work. / There has been a power failure or the power cord has been disconnected during tape operation. [. . . ]