User manual SONY TSW50

[. . . ] The HF2BR system achieves a remarkable reduction in the unpleasant port noise by making low frequency-sound pass through this filter. Diagram Duct (1) Port (1) L I ! Acoustic low pass filter 2 $%'I'4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Xa-%m #@zf3z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] using magnetic cording away from the unit as the recorded information may be erased or some noise may be added on cassette tapes. Should any problem occur, disconnect the AC cord and refer servicing to qualified personnel only. 4 q q q 5 ------ . ----- ----- POSITIONING -- Because low-frequency sound reproduced by the powered sub woofer is mostly non-directional, the listener will be unable to localize the bass source. Accordingly, the powered subwoofer provides maximum flexibility in terms of positioning. For the most effective low-frequency sound, the powered subwoofer should be placed on the floor close to a wall or in a corner of the room. CONNECTIONS Connect the speaker cords before connecting the AC cord. Connect in u way if your stereo system has a SUPER WOOFER output jack. Never connect in both of u and u ways simultaneously. uConnecting an AIWA stereo system with a SUPER. WOOFER output jack (RCA phono jack) to the powered subwoofer Preparations Turn off the power of this unit. 1 Connect the SUPER WOOFER jack on the stereo system side O to the INPUT 1 (FROM SUPER WOOFER TERMINAL) jack on the powered subwoofer @ with the supplied connecting cord. 2 Set the INPUT SELECT switch to "l". uConnecting JJ a stereo system with speaker terminals to the powered subwoofer You will need a pair of optional speaker cords. Preparations Turn off the power of the stereo system and remove the speaker cords from the speaker terminals on the system. dD `"'"m 1 Connect the stereo system speaker terminals @to the INPUT 2 (FROM SPEAKER OUT) terminals on the powered subwoofer @ with optional speaker cords ~. Make sure the L and R, @ and @ cords are connected correctly. 2 Using the speaker cords removed in "Preparations" above, connect the right and left speakers @) @to the SPEAKERS OUT terminals on the powered subwoofer o. 3 Set the INPUT SELECT switch to "2", Connecting the AC cord Connect the AC cord to a wall outlet. @ d I G) q Use Ieft/right speakers whose impedances correspond with the value specified in the stereo system. c 6 &3&s@ 1 2 1 3 2 3 7 OPERATION ADJUSTING THE VOLUME BALANCE Before listening, adjust the volume balance between the powered sub woofer and the left and right speakers on the connected stereo system. 1 Press the POWER button. The indicator on the left side of the button lights up. 2 Start playback on the connected stereo system. 3 Adjust the volume of the powered sub woofer. Moderate volume setting To get natural bass sounds, adjust the volume of the powered sub woofer according to its position and the graphic equalizer setting of the stereo system. Adjustment examples 1 Set the VOLUME control to a little lower than the middle when the woofer is placed on the floor and the graphic equalizer is set to off. 2 Set the VOLUME control to the middle when the woofer is positioned higher than the floor and the graphic equalizer is set to off. m wTo avoid overloading the powered sub woofer, do not set the volume of the stereo system so high that the sound is distorted. q Low frequency sounds may be distorted when they are emphasized by the graphic equalizer on the stereo system. Adjust the VOLUME control on the powered sub woofer or the graphic equalizer on the stereo system. q If the powered sub woofer will not be used for a long period of time, press the POWER button to turn off the power, and unplug the AC cord from the wall outlet. CHANGING THE PHASE + El Depending upon the room or the characteristics of the right and left speakers, sound from the powered sub woofer may seem unnatural or unusually loud or soft. In this case, try changing the PHASE switch. Set to the NORMAL or REVERSE position, whichever sounds better. USING THE AUTO POWER FUNCTION + u Before using this function, make sure the POWER button is set to ON. [. . . ] Ajuste el control VOLUME del altavoz de subgraves activo o del ecualizador grafico del sistema estereo. q Cuando no vaya a utilizar el altavoz de subgraves activo durante mucho tiempo, presione el boton POWER para desconectar la alimentacion, y desenchufe el cable de alimentacion de CA del tomacorriente de la red. q MAX CAMBIO DE LA FASE: + u Dependiendo de la sala o de Ias caracter[sticas de Ios altavoces derecho e izquierdo, el sonido del altavoz de subgraves activo puede resultar innatural, o excepcionalrnente fuerte o suave. En tal case, pruebe a cambiar el selector PHASE. Pongalo en la position NORMAL o REVERSE, la que ofrezca el mejor sonido. UTILIZATION DE LA FIJNCION DE ENCENDIDO AUTOMATIC -+ El Antes de utilizar esta funcion, asegurese de que el boton POWER este en ON. [. . . ]