User manual SONY UCP-8060 OPERATING MANUAL

[. . . ] UNIVERSAL CONTROL PANEL UCP-8060 OPERATION MANUAL [Japanese/English] 1st Edition (Revised 1) oe{OE ^`S, , , , Iy[V}jA iA/\~ "d<Ci, ͷA^`S, , , , '^Z, Z, , , , ƷAη, S"d, , , , , ZS, `, , , , ǷlgZOE, , , , , , , , , , ASOE, , B ZOE, h, , , , ZY, , , , K, , Z, , -, , , B ~'{>B B\e> x\ ^`S, , , , '^Z, Z, 4 ` 6 y[W, '^Z, , , -, ", , -, , , B --dLSfl "lgح LB \A 'S"_OEY, ZZ{, , 'SS^`S, Zg--p, , , , , , -, , , ɷA'S"_OEY, ZZ{, , , , , , , , , , , , B"_OEY, "--e, "--p, , , , , ͷA\j[, T[rX'S"Z, , , c<'S"Z, , `S'k, -, , , B \A OE̷, , , Zg--p, 'Z~, , d. . . Lfl" Li, , Q^ Lح"B \j[, T[rX'S"ZҷA, , , c<'S"Z, , ~A--, -, , , B oe^A^ٷ, <N, , , L , , A"o ", , m a d, , B b d, , R[hR[h>B c \j[TrXSAcSCB s~L "o swL m fid, , LA`B 2 ^`S, , , , ZY OEx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 '^ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Then release the button. Setting the Auto Start If the Auto Start function has been set with the operation software, the top page of the operation software automatically appears after the Main Screen of the UCP8060 appears when the power is supplied to the unit. Setting the Auto Start To set the Auto Start function, follow the procedures below. 1 2 3 Select the operation software to which the Auto Start function is to be set on the Main Screen. The Menu display appears. Confirming of the Basic Information Press the select L and R buttons while holding the function 1 button pressed for more than 3 seconds until the function 1 button lights. The Basic Information of System [BIOS] Utility appears on the screen to show the FPGA version, MAC address, etc. You can start the BIOS Utility from the Shutdown display. For details, see "Terminating the UCP-8060" on page 35. Select Auto Start. The Auto Start display appears. Auto Start ON OFF Exit Save 4 5 Select ON. The Menu display appears. Basic Operations 35 6 Press the select L button (Back). The Main Screen appears. System Setup The following items are enabled with the SYSTEM SETUP UTILITY. Device Control Adjusting the brightness of the display window Adjusting the sound level for the touch-panel beep and testing it Adjusting the sensitivity of TouchEngine Specifying ON or OFF for the touch-panel beep Setting the date and time Setting the TCP/IP address Calibrating the relationship between the display and touch panel Scribble test Self-diagnosis Canceling Auto Start Perform the same procedures as for setting Auto Start and select ON instead of OFF in Step 4. If you set Auto Start for other operation software, the Auto Start function set on this software canceled. Interrupting Auto Start Press the select L button (Menu) within about two seconds after the Main Screen appears after turning the UCP-8060 on, and Auto Start is interrupted. Formatting a Memory Stick 1 Start the BIOS Utility. For starting the BIOS Utility, see "Confirming of the Basic Information" on page 35. Activating the SYSTEM SETUP UTILITY Select SYSTEM SETUP UTILITY on the Main Screen to activate it. The SYSTEM SETUP UTILITY display appears. SYSTEM SETUP UTILITY Device Control Version 1. xx 2 3 4 5 Insert a Memory Stick into the Memory Stick slot with the label side up. Press the select R button (Memory Stick Format). Normally press the select R button (Quick). Press the select R button (YES). Adjust Time Set TCP/IP Config Calibrate Touch Panel Scribble Test Self Diagnosis Once "DONE" appears on the screen, formatting of the Memory Stick is complete, and the MSSONY/PRO/UCP folder is created. Note Exit 03:13:00 Formatting of the Memory Stick deletes all files stored in the Memory Stick. Select an item you wish to set. For details on selecting an item, see "Basic Operations" on page 34. Soft Reset Press the select L and R buttons simultaneously for more than 3 seconds. A soft reset of the UCP-8060 is executed. Functions of Each Menu Item Device Control Adjust each item with the following procedures: 1 2 3 Turn the jog roller to select an item to be adjusted. Press the jog button to adjust the item. Press the jog roller to register your adjusted value. 36 System Setup 4 Press the select R button when you are finished making adjustments. The adjusted values are stored. Set TCP/IP Config. The IP Address, Netmask, Gateway, and DNS have been set at the factory, but you can change them as required. To cancel an adjusted value, press the select L button. LCD Brightness Adjust the brightness of the display window in seven steps. [. . . ] To use a "Memory Stick" that has been formatted on a personal computer, the "Memory Stick" must be reformatted on this product. If it is not reformatted, all data stored on the "Memory Stick" will be lost. For details on formatting a "Memory Stick, " see "Formatting a Memory Stick" on page 36. Write-protect tab Labeling position Status Indicator When you set the "Memory Stick" erasure prevention switch to " LOCK, " data cannot be recorded, edited, or erased. Position and shape of the write-protect tab may differ depending on the "Memory Stick" to be used. [. . . ]