User manual SONY VAIO VGN-BX41XN

[. . . ] 3-048-646-14(1) Integrated Remote Commander Operating Instructions RM-AV2100/AV2100B © 2000 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. WARNING You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. NOTICE FOR THE CUSTOMERS IN THE U. S. A. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] To reset them to the factory settings, follow the steps below. The key operations programmed for that button are displayed in order. 26 1 While pressing COMMANDER OFF, press the SYSTEM CONTROL button (1 or 3). Notes on System Control Operations · If the remote control detectors of the components are too far apart, or if something is blocking them, some of the components may not operate consecutively even after you press the SYSTEM CONTROL button. · If some of the components did not operate correctly because of the above or for any other reason, always set all the components back to the states they were in before you pressed the SYSTEM CONTROL button. Failure to do this can result in incorrect operation when you press the SYSTEM CONTROL button again. · Some components may not always be powered on by the System Control function. This is because the power of the component gets on and off alternatively when receiving the power on/off signal. In this case, check the operating component's power on/off state before using the system control function. · If the system control function does not work correctly, see also "Tips for programming the System Control functions" on page 25. The programmed key operations are displayed in order. 2 While pressing the RESET key, press the SYSTEM CONTROL button (1 or 3). When the contents of its program are cleared, all the components names flash. 3 While pressing the RESET key, press the SYSTEM CONTROL button (1 or 3) again. When it is reset to the factory setting, the programmed operations are displayed in order. Note The interval setting (page 30) is not reset to the factory setting, even if you perform these steps. Continued 27 Executing a Series of Commands -- System Control Functions (continued) Example: To program the procedure on page 23 for the VCR3 button Programming a series of commands to the Component Select buttons As with the SYSTEM CONTROL buttons, you can also program a series of operating commands for the Component Select buttons (up to 16 steps). To execute the commands programmed on a Component Select button by the System Control function, press the button for more than 2 seconds. Notes · The programmed commands are executed when you press a Component Select button for more than 2 seconds. When you press the button for less than 2 seconds, it works as the normal Component Select button, and the corresponding touch-keys are displayed. · See also "Tips for programming the System Control functions" on page 25 and "Notes on System Control Operations" on page 27. 1 While pressing COMMANDER OFF, press VOLUME+ and VCR3. All the component names flash. If a series of commands is already programmed for that button The programmed operations are displayed in order. To program a new series of operations, clear the program first (page 29). 2 Follow Steps 2 to 5 on pages 24 and 25. 28 Notes · You can program the System Control functions for a Component Select button on which the Power-On function (page 31) has been programmed. In this case, the Power-On function is overwritten and cannot be used. If you clear the System Control functions for the button, the Power-On function is resumed, and you can use it again. · You cannot program the System Control functions for a Component Select button for which a signal has been programmed by "learning" (page 32). ("NG" flashes on the display. ) · You can program a signal for a Component Select button by "learning" (page 32) for which the System Control functions have been programmed. In this case, the System Control function is overwritten and cannot be used. If you clear the "learned" signal on the button, the System Control function is resumed and you can use it again. · You can program the Power-On function (page 31) for a Component Select button for which a System Control function has been programmed, but the Power-On function cannot be used. If you clear the System Control function from the button, you can use the Power-On function. · If you interrupt the procedure at any point for over two minutes, the setting mode ends and the series of commands will be programmed to that point. In this case, clear the program and start again from Step 1 to set the entire program from the beginning. You can not continue from where you let off. [. . . ] · The component codes are changed or a new signals have been learned for a key or button that has been programmed with a series of commands. In this case, the new signals are transmitted when the series of commands is executed. See "Changing the interval between operation steps" (page 30) and set a longer interval. You hear beeps ("pip, pip") and "NG" flashes. "NG" appears during learning. A system control program does not function correctly. 56 Symptom Remedy The power of the · This Commander is preset at the factory to switch the power off Commander turns off by automatically after 10 minutes if left unused. [. . . ]