User manual SONY VAIO VGN-CS110E/Q

[. . . ] Be careful not to spill liquids, or drop any flammable or metal objects in the camera body. Do not wrap the camera in cloth or other material while in operation. Locations subject to strong vibration · Near generators of strong electromagnetic radiation such as TV or radio transmitters For the customers in the USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Use a blower to remove dust from the surface of the lens or optical filter. Clean the exterior with a soft, dry cloth. If the camera is very grimy, apply a cloth soaked in a mild detergent then wipe with a dry cloth. Do not apply organic solvents such as alcohol which may damage the finish. Before operating the unit, please read this manual thoroughly and retain for future reference. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. To install on a tripod, you will need to install the VCT-ST70I tripod adaptor to the camera on the reference holes of the bottom of the camera. XC-ST70/ST70CE: interline transfer 2/3 type CCD XC-ST51/ST51CE/ST50/ST50CE: interline transfer 1/2 type CCD XC-ST30/ST30CE: interline transfer 1/3 type CCD Effective picture elements (horizontal/vertical) XC-ST70/ST51/ST50/ST30: 768 × 494 XC-ST70CE/ST51CE/ST50CE/ST30CE: 752 × 582 Optical blank 43 elements on each horizontal line CCD vertical drive frequency XC-ST70/ST51/ST50/ST30: 15. (Factory setting: EXT) 5 VIDEO OUT (Video signal output) connector (BNC) You can use this connector for video signal output from the camera module. Do not use any other settings for Restart reset/External trigger shutter mode except those shown in Figure F-c. Using other settings may cause the camera to malfunction. 0 75 termination switch Turn off if you do not terminate. (Factory setting: ON) qa TRIG polarity switch Select + or ­ according to the trigger pulse input from an external unit. (Factory setting: +) qs DC IN/SYNC (DC power input/sync signal I/O) connector (12-pin) Connect a CCXC-12P05N camera cable to this connector the +12 V DC power supply and the video signal output from the camera module. When a sync signal generator is connected to this connector, the camera module is synchronized with the external sync signals. 3 Vp-p ±6 dB) HD/VD (HD/VD level: 2 to 5 Vp-p) External sync allowable frequency ±1% (of horizontal sync frequency) H Jitter Within ±50 nsec Scanning system XC-ST70/ST51/ST50/ST30: 525 lines XC-ST70CE/ST51CE/ST50CE/ST30CE: 625 lines 2:1 interlace/noninterlace (automatically switched according to input signal) Video output 1. [. . . ] 3 Vp-p ±6 dB) HD/VD (HD/VD level: 2 to 5 Vp-p) External sync allowable frequency ±1% (of horizontal sync frequency) H Jitter Within ±50 nsec Scanning system XC-ST70/ST51/ST50/ST30: 525 lines XC-ST70CE/ST51CE/ST50CE/ST30CE: 625 lines 2:1 interlace/noninterlace (automatically switched according to input signal) Video output 1. 0 Vp-p, sync negative, 75 unbalanced Horizontal resolution XC-ST70/ST51/ST50/ST30: 570 TV lines XC-ST70CE/ST51CE/ST50CE/ST30CE: 560 TV lines Vertical effective lines XC-ST70/ST51/ST50/ST30: 485 lines (with 2:1 interlace) XC-ST70CE/ST51CE/ST50CE/ST30CE: 575 lines Sensitivity XC-ST70/ST70CE/ST50/ST50CE: 400 lx, F8 ( compensation ON, XC-ST51/ST51CE: 400 lx, F11 0 dB) XC-ST30/ST30CE: 400 lx, F5. 5 mm (1 3/4 × 1 3/16 × 2 3/8 inches) Mass XC-ST70/ST70CE: 105 g (4 oz) XC-ST51/ST51CE/ST50/ST50CE/ST30/ST30CE: 110 g (4 oz) Accessories Lens mount cap (1) Operating Instructions (1) Design and specifications are subject to change without notice. The following phenomena that may appear in images are specific to CCD (Charge Coupled Device) image sensors. [. . . ]