User manual SONY VAIO VGN-CS290NDB

[. . . ] Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] After the last track, "CHECK END" appears. CHECK on the remote repeatedly until the number of the track to be erased lights up, then press CLEAR. 1 Select the disc tray with a DISC 1~3 button. 2 Select the track by turning the jog dial. p once in stop mode or twice while playing. Playing CDs without interruption ­­ Non-Stop Play You can play CDs without pausing between tracks. (Power) 3 Clear a track from the end Clear a specific track Add a track to the program Clear the entire program 6 6 Tips · The program you made remains in the CD player even after it has been played back. Press CD (P to play the same program again. · If "--. --" appears instead of the total playing time during programming, this means: ­ you have programmed a track number which exceeds 20. ­ the total playing time has exceeded 100 minutes. 1 1 2 2 Press FUNCTION repeatedly until "CD" appears in the display, then place a CD. Press NON-STOP to light the indicator. "NON-STOP PLAY" appears in the display. 3 Press CD (P. To cancel Non-Stop Play Press NON-STOP so that the indicator goes out and "NON-STOP OFF" appears in the display. 22 The Tape Deck Recording on a tape manually You can record from CD, tape, or radio as you like. For example, you can record just the songs you want or record from the middle of the tape. The recording level is adjusted automatically. (Power) 4 Press DIRECTION repeatedly to select A to record on one side. Tip When you want to reduce the hiss noise in low-level high-frequency signals, press DOLBY NR so that "DOLBY NR" appears after pressing CD SYNC. 25 DJ Effects Looping part of a CD -- Loop With the loop function, you can repeat part of a CD during playback. This lets you create original recordings. (Power) Flashing part of a CD -- Flash With the flash function, you can "flash" the CD sound during playback. This lets you create original recordings. (Power) 6 6 6 6 LOOP Jog dial FLASH Jog dial / Press and hold FLASH during / Press and hold LOOP during playback at the point you want to start the Loop function, and release to resume normal play. To adjust the loop length Turn the jog dial while holding LOOP (or press FILE SELECT > or . while holding LOOP on the remote) to select different loop lengths (LOOP 1~20). playback at the point you want to start the Flash function, and release to resume normal play. To adjust the flash length Turn the jog dial while holding FLASH (or press FILE SELECT > or . while holding FLASH on the remote) to select different flash lengths (FLASH 1~20). To use LOOP and FLASH together Press and hold both LOOP and FLASH at the same time. Notes · The loop and flash length cannot be adjusted during this operation. Adjust the loop and flash lengths independently beforehand if necessary. · To record the loop or flash effect, use the analog MD/VIDEO (AUDIO) OUT connections or this unit's tape deck. 26 Sound Adjustment Adjusting the sound You can reinforce the bass, create a more powerful sound, and listen with headphones. FILE SELECT Notes · With some songs, the music will sound distorted when you use the DBFB system with the sound effect if the bass is too strong. Set the DBFB to "DBFB " or "OFF", or cancel the sound effect (see page 28). [. . . ] ·The record/playback heads are magnetized. Demagnetize them (see "Demagnetizing the tape heads" on page 41). There is excessive wow or flutter, or the sound drops out. ·The capstans or pinch rollers are dirty. [. . . ]