User manual SONY VAIO VGN-CS320J

[. . . ] Refer servicing to qualified personnel only. Don't throw a battery, dispose it as the injurious wastes. WARNING NOTICE FOR THE CUSTOMERS IN THE U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Then press TUNING ­ or + (or ­ or + on the remote) repeatedly to tune in the desired station (Manual Tuning). · Press TUNING MODE on the remote repeatedly until "AUTO" appears in step 2 then press TUNING ­ or + (or ­ or + on the remote). The frequency indication changes and the scanning stops when the system tunes in a station (Automatic Tuning). To cancel Automatic Tuning · The preset stations are retained for about a week even if you disconnect the power cord or if a power failure occurs. · When a new station is memorized, the station formerly memorized at that preset number is erased. Press TUNING MODE on the remote. Tips · If noise is heard while listening to an FM station, remove the FM antenna from the rear panel and place the antenna outside the cabinet. · To improve broadcast reception, adjust the supplied antennas, or connect a commercially available external antenna. · When an FM stereo program has static noise, press FM MODE on the remote repeatedly until "MONO" appears. There will be no stereo effect, but the reception will improve. 14 Sound Adjustment Adjusting the sound Generating a more dynamic sound -- DSG You can use the DSG (Dynamic Sound Generator) function to produce a more powerful sound. Press DSG on the remote. Adjusting the sub woofer You can adjust the sound of the sub woofer to suit the sound source and adjustment on the system. 1 Start playing the sound source. Male vocal tunes and voice containing bass sounds are most suitable for adjustment. The volume for the system should be set to the same level as usual. 2 Turn CUT OFF FREQ on the sub woofer to adjust the cut-off frequency. Tuner/Sound Adjustment Each time you press the button, the display changes cyclically as follows: DSG 1 t DSG 2 t DSG OFF When DSG is on, "DSG" lights up. Press DSG on the remote repeatedly to cancel DSG. 3 Turn LEVEL on the sub woofer to adjust the volume level of the sub woofer. 4 Press PHASE on the sub woofer repeatedly to select the phase polarity. Selecting the surround effect Press SURROUND on the remote. The polarity changes as follows: NORMAL (normal) y REVERSE (reverse) 5 Repeat step 2 to 4 to adjust for your preference. Tips "SURR" appears in the display. Press again to cancel surround effect. Adjusting the bass Press BASS + or ­ on the remote repeatedly to adjust the bass. You can adjust the bass in 7 steps (from ­3 to +3). Adjusting the treble Press TREBLE + or ­ on the remote repeatedly to adjust the treble. You can adjust the treble in 7 steps (from ­3 to +3). Tips · The power indicator lights red in standby mode. During playing, the indicator turns green. To connect optional components, remove the small rear cover first. To the audio input jacks of an optional component To the audio output jacks of an optional component * Select "PC/TAPE" to use an optional component connected to the PC/TAPE jacks as the sound source. 8 Press ENTER on the remote. The start time, the stop time, and the sound source appear in turn, before the original display returns. "DAILY" lights up. 9 Press ?/1 to turn off the system. Other Operations To Do this Timer/Optional Components Check the setting Press CLOCK/TIMER SELECT on the remote repeatedly until "DAILY" appears. The start time, followed by the stop time, the sound source appears, then original display appears. Press CLOCK/TIMER SELECT on the remote repeatedly until "TIMER OFF" appears. PHONES jack To the digital input jack of a digital component Do this Change the setting Cancel the timer To Notes · If the system is on about 30 seconds before the preset time, the Daily Timer will not be activated. · Do not operate the system from the time the system turns on until the play starts (about 30 seconds before the preset time). · Once you set the Daily Timer, it functions every day until you cancel it. Make a digital recording to a digital component Make an analog recording to an analog component Listen to the connected optional component Listen through the headphones Connect a optical cable. Connect the audio cords. Press FUNCTION repeatedly until "PC/TAPE" appears (or press PC/TAPE on the remote). Connect the headphones to the PHONES jack. 17 Additional Information On installing Precautions The nameplate is located on the bottom exterior. On safety · The glass over the display window on the cover is made of tempered glass. Under normal conditions, this tempered glass is more shock resistant and able to bear more weight than ordinary glass. This glass, however, may shatter if it receives a sharp blow or if it is scratched. · The system is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the system itself has been turned off. · Unplug the system from the wall outlet if it is not to be used for an extended period of time. [. . . ] · Turn LEVEL on the sub woofer counterclockwise. · Turn CUT OFF FREQ on the sub woofer to adjust cut-off frequency. Howling occurs. · Set the proper band and frequency (see page 13). · Connect the antenna properly (see page 8). · Find a place and an orientation that provide good reception, then set up the antenna again. [. . . ]