User manual SONY VAIO VGN-NS220J/S

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Notice If static electricity or electromagnetism causes data transfer to discontinue midway (fail), restart the application or disconnect and connect the communication cable (USB, etc. ) again. 2 For customers in the U. S. A. If you have any questions about this product, you may call: Sony Customer Information Center 1-800-222SONY (7669). The number below is for the FCC related matters only. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Software that can record the video signal must be installed on your computer beforehand. A/V jack 1 (yellow) (white) (Red) VCR Computer 2 To i. LINK (IEEE 1394) jack DV Interface :Signal flow i. LINK cable (optional) i. LINK jack A/V connecting cable (supplied) Connect the A/V connecting cable to your camcorder or the Handycam Station. The A/V jack accepts analog signals. setting is [LCD PANEL]. ) 1 Turn on the analog video unit. 2 Slide the POWER switch of your camcorder down to turn on the PLAY/EDIT lamp. Use the supplied AC Adaptor as the power source. A/V connecting cable with S VIDEO (optional) When connecting to another device via the S VIDEO jack, by using the A/V connecting cable with an S VIDEO cable (optional), pictures can be reproduced more faithfully than with the supplied A/V cable connection. Connect the white and red plugs (left/right audio) and S VIDEO plug (S VIDEO channel) of an A/V connecting cable (optional). In this case, the yellow (standard video) plug connection is not necessary. S VIDEO connection only will not output audio. 3 On the LCD screen, touch 80 Set [DISP OUTPUT] to [LCD PANEL] on the menu (p. (The default [MENU] (STANDARD SET) [A/VDV OUT] [ON] . 4 Start playback on the analog video unit. 5 Start capturing procedures on your computer. Regarding operation, refer to the operating instructions supplied with the software or the on-line help. After capturing images and sound, stop capturing procedures on your computer, and stop playback on the analog video unit. · The bundled software Picture Package or ImageMixer VCD2 does not support the signal convert function. · You may not be able to output the pictures correctly depending on the condition of the analog video signal input to your camcorder. 10). The CHG (charge) lamp flashes while the battery pack is being charged. · Attach the battery pack to the camcorder correctly. If the problem persists, disconnect the AC Adaptor from the wall outlet and contact your Sony dealer. The battery pack may be damaged. The power turns off frequently although the remaining battery time indicator indicates that the battery pack has enough power to operate. · A problem has occurred in the remaining battery time indicator, or the battery pack has not been charged enough. Fully charge the battery again to correct the indication (p. 10). Troubleshooting The remaining battery time indicator does not indicate the correct time. · The temperature of the environment is too high or too low, or the battery pack has not been charged enough. · Fully charge the battery again. If the problem persists, replace the battery pack with a new one. · The indicated time may not be correct depending on the environment of use. When you open or close the LCD panel, it takes about 1 minute to display the correct remaining battery time. The battery pack is quickly discharged. · The temperature of the environment is too high or low, or the battery pack has not been charged enough. · Fully charge the battery again. If the problem persists, replace the battery pack with a new one. [. . . ] 71, 72 WIPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Wrist strap . . . . . . . . . . . . . . . . . . . . . . . . . . 106, 107 Z Zero set memory . . . . . . . . . . . . . . . . . . 32 ZERO SET MEMORY button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]