User manual SONY VAIO VGN-SR490JCW

[. . . ] The FCC regulations also require that computing devices used in the U. S. display the agency's label and that the related documentation include the following statement: NOTICE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Connect all equipment together, including the static­free mat, static straps, routing nodes, and peripheral units. Keep uninstalled printed circuit boards in their protective antistatic bags. Once you have removed the printed circuit boards from their protective antistatic bags, handle them by their edges. 3 Warnings and Cautions WARNING: Removing device cover may expose sharp edges in equipment chassis. To avoid injury, use care when installing customer add­ on devices WARNUNG: Das Entfernen der Geräteabdeckung legt die scharfen Kanten im Inneren des Gerätes frei. Um Verietzungen zu vermeiden, seien Sie vorsichtig beim Einbau von zusätzlichen Bauteilen, die vom Kunden selber eingebaut werden können AVERTISSEMENT: Des bords tranchants du châssis de l'équipement peuvent être exposés quand le cache de l'unité n'est pas en place. Pour éviter des blessures, faire très attention lors de l'installation de modules supplémentaires par le client. WARNING: Disconnect power plug from wall outlet or source power before moving or removing the device, or installing add­on components. WARNUNG: Entfernen Sie die Stromzuführung von der Steckdose oder der Stromquelle bevor Sie das Gerät bewegen, abbauen, oder zusätzliche Bauteile installieren. AVERTISSEMENT: Débrancher la fiche de la prise de courant ou de la source d'alimentation électrique avant de déplacer ou de retirer l'unité, ou avant d'installer des modules supplémentaires. CAUTION: System power cord must be plugged into an accessible dedicated ac mains receptacle. VORSICHT: Das System­Netzanschlußkabel muß an eine zugängliche spezielle Wechselstrom­Hauptzuführungssteckdose angeschlossen werden. ATTENTION: Le fil d'alimentation électrique du système doit être branché dans une prise de courant c. a. spécialisée accessible. 4 700 Series Workstation to B­Class Workstation Trade­Up Installation Instructions. These instructions document the installation of a B­Class workstation when trading up from your 700 Series workstation. The procedures you perform may vary depending on the configuration of your Series 700 workstation. The installation procedures are divided into the following areas: D D D Removing components from your Series 700 workstation that can be used in the B­Class workstation. Installing components from your Series 700 workstation into the B­Class workstation. Power up the B­Class workstation CAUTION: Although the chances of corrupting your system are very small, you must back up your system, before you shut down your system to perform this upgrade, . Ensure the jumpers on your disk drive are set to the appropriate configuration. LED Front View J3 SCSI ID Second 5 Drive 1 2 3 4 5 6 7 8 9 10 SCSI ID Second 5 Drive NOTICE: If applicable change the SCSI ID to 5 as shown Do not change any other jumpers Quantum Disk Drive Models ­ VP32210 VP31110 DEC Disk Drive Model ­ DSP3107LS SONY Part Number ­ 9164­0395 Hewlett-Packard Disk Drive Models ­ C3324A C3325A SONY Part Numbers ­ 0950­2601 0950­2606 Figure 2. Internal Storage Device Jumper Settings C. The CD ROM drive jumper settings are shown in Figure 5. Ensure the jumpers on your CD ROM drive are set to the appropriate configuration. To install the internal storage device(s) in your B­Class workstation, refer to Figure 6 and the Model B132L/B160L Owner's Guide (A4190­90014). NOTICE:When using a hard disk from your Series 700 workstation, it cannot be configured as the boot drive and must be installed in position 2 (front position). 9 LED SCSI ID Second Drive 1 2 34 56 5 NOTICE: A0, A1 and A3 are the SCSI ID jumpers. The jumpers TE, SS, WS and I/O should be removed. The jumper EP and INT should be in place SCSI ID 5 Quantum Disk Drive Model ­ LPS1080S SONY Part Number ­ 9164­0395 NOTICE: The first three jumpers (1, 2, and 3) should be removed. The SCSI ID jumpers are jumpers 4, 5, and 6. Seagate Disk Drive Models ­ ST32430N ST31230N ST31200N SONY Part Numbers ­ 0950­2601 0950­2606 Figure 3. [. . . ] To install an EISA card in your B­Class workstation see Figure 7, and refer to the Model B132L/B160L Owner's Guide (A4190­90014). NOTICE:The X. 25 link and the 10/100VG LAN Link require SONY­UX 10. 20 drivers to be installed. 4. Graphics Cards To remove and replace any of the graphic cards, perform the following: A. To remove a graphic card from your Series 700 system refer to your Series 700 Owners Guide. [. . . ]