User manual SONY VAIO VGN-TZ198N/R

[. . . ] Always use a power cord with a properly grounded plug, such as the one provided with this equipment, or one in compliance with your national regulations. This PC is disconnected from the power by removing the power cord from the power outlet. This means the PC must be located close to a power outlet that is easily accessible. For your safety, never remove the PC's cover without first removing the power cord from the power outlet, and any connection to a telecommunications network. [. . . ] Select the option and press <Enter>. Press <F5> to switch between color and monochrome modes. Options Configure/View Host Adapter Settings SCSI Disk Utilities Arrow keys to move cursor, <Enter> to select option, <Esc> to exit Use the and keys and the key to make selections in the SCSISelect utility. Press at any time to return to the previous menu. English 1 Configuring the SCSI Bus It is recommended that you do not change these settings. Configure/View Interface Settings Menu SCSISelect(TM) Utility v1. xxx Configuration SCSI Bus Interface Definitions Host Adapter SCSI ID . Enabled Host Adapter SCSI Termination . . . . . . . . . . . . . . . . . . . Automatic Additional Options Boot Device Options . Press <Enter> SCSI Device Configuration . Press <Enter> Advanced Configuration Options . Press <Enter> <F6> - Reset to Host Adapter Defaults BIOS Information Interrupt (IRQ) Channel . F800h SCSI Channel Interface Definitions: · · Host Adapter SCSI ID Changes the adapter SCSI ID from its default value of 7. SCSI Parity Checking Enable or disable host adapter SCSI parity checking. Most currently available SCSI devices do support SCSI parity. You should disable SCSI Parity Checking if any of the attached SCSI devices do not support SCSI parity. · Host Adapter SCSI Termination It is recommended that you leave this field on its default setting of Automatic. This option is not supported by some SCSI devices. Some SCSI devices require a jumper to be changed before they can respond to this command. · BIOS Multiple LUN Support More advanced SCSI devices can have several logical units (LUN). This option determines whether booting a SCSI device that has multiple LUNs is supported. Set this option to Yes if your boot device has multiple LUNs. It is set to no by default. · Include in BIOS Scan This setting, when set to Yes, allows the SCSI device to be controlled by the host adapter with this SCSI ID. When set to No, the adapter does not control the SCSI device. English 5 Configuring the SCSI Bus Advanced Configuration It is recommended that these settings are not changed. Options Menu Advanced Configuration Options Plug and Play Scam Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disabled Extended BIOS Translation for DOS Drives > 1 GByte . . . . . . . . . . . . Enabled Reset SCSI Bus at IC Initialization. . . . . . . . . . . . . . . . . . . . . . . . . . . . Enabled Options Listed Below Have NO EFFECT if the BIOS is Disabled Host Adapter BIOS (Configuration Utility Reserves BIOS Space). . Enabled Support Removable Disks Under BIOS as Fixed Disks. . . . . . . . . . . . . . Boot Only Display F6 Message During BIOS Initialization. . . . . . . . . . . . . . . . . . [. . . ] This option is enabled by default. · Support Removable Disks Under BIOS as Fixed Disks When Boot Only is selected, only the removable media drive designated as the boot device is treated as a hard disk drive. If All Disks is selected, all removable-media drives supported by the BIOS are treated as hard disk drives. No removable-media drives are treated as hard disk drives when Disabled is selected. In this case, removable-media drives must be controlled through operating system drivers. 6 English Configuring the SCSI Bus · Display <Ctrl><A> Message During BIOS Initialization When enabled, this option displays the message Press <Ctrl><A> for SCSISelect(TM) Utility! [. . . ]