User manual SONY VAIO VGN-TZ390UDX

[. . . ] Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U10 Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST320423A, ST315323A, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST310212A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ultra ATA Interface Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Although CE-marked Seagate drives U10 Family Product Manual, Rev. A 15 comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products. Australian CE-Tick (N176) If these models have the C-Tick marking, they comply with the Australia/ New Zealand Standard AS/NZS3548 1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of Australia's Spectrum Management Agency (SMA). 1. 12. 3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required. has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc. ) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception. This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. Other labels are used to seal out dirt and contamination. 18 U10 Family Product Manual, Rev. A 2. 2 Jumper settings 2. 2. 1 Master/slave configuration The options jumper block shown in Figure 2 is used to configure the drive for operation. It is the 6-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8. Drive as master with a non-ATA-compatible slave. Set a jumper on pins 5 and 6 and a jumper on pins 7 and 8. Use this jumper setting only if the drive does not work as a master with no jumpers installed. Options jumper block (J8) Master or single drive Drive is slave Master with a non-ATAcompatible slave Cable select 7531 8642 Figure 2. Master/slave jumper settings U10 Family Product Manual, Rev. A 19 2. 2. 2 Cable-select option Computers that use cable-select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. [. . . ] Ultra DMA mode 0 is currently active. U10 Family Product Manual, Rev. A 9 10 11 12 Bit 13 Ultra DMA mode 1 is currently active. Word 93 1=80-conductor cable detected, CBLID above VIH 0=40-conductor cable detected, CBLID below VIL 29 3. 1. 3 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. [. . . ]