User manual SONY VAIO VGN-Z590NGB

[. . . ] Double-click on the listing for your new modem. This will show you the modem's properties. If Windows configured the modem correctly, the section labeled "Device status" should read "This device is working properly. " If this is not the case, you might have a hardware resource conflict. To correct this, click on the Resources tab to view and manually change your configuration to avoid the conflict. [. . . ] Make sure the modem is properly initialized by the communication software. Your modem may have been improperly initialized by the software because you have selected an incorrect modem type. Select "Lucent Based Data/Fax/Voice/DSVD Modem" in your application software. Alternatively, you should use the "Generic Hayes Modem" option for data-only applications. You may also be prompted to enter an initialization string" by the software. Use AT&F as your initialization string. 2. Modem dials but does not connect. 1. Make sure the phone line is working properly. A noisy line will prevent proper modem operation. Try connecting to another modem number to ensure the problem is not related to the answering modem. Modem makes a connection but no data appears on your screen. 1. Make sure all communication parameters (baud rate, data, stop, and parity bits) are properly configured and are identical on both sides. Be certain hardware flow control (RTS/CTS - default) is enabled in both the modem and the communication software. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect proper operation of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. The FCC prohibits this equipment to be connected to party lines or coin-telephone service. In the event that this equipment should fail to operate properly, disconnect the equipment from the phone line to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or vendor. FCC Class B Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · NOTE: Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio / TV technician for help 1) Shielded cables, if any, must be used in order to comply with the emission limits. 2) Any change or modification not expressly approved by the Grantee of the equipment authorization could void the user's authority to operate the equipment. FCC Fax Branding Statement The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine, or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges. ) In order to program this information into your fax machine or fax/modem consult your fax machine user's manual or software user's manual for setup instructions. DOC Compliance Information NOTE: NOTICE: The Canadian Department of Communications label identifies certified equipment. [. . . ] 2) Any change or modification not expressly approved by the Grantee of the equipment authorization could void the user's authority to operate the equipment. FCC Fax Branding Statement The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine, or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges. ) In order to program this information into your fax machine or fax/modem consult your fax machine user's manual or software user's manual for setup instructions. DOC Compliance Information NOTE: NOTICE: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. · Before installing this equipment, users ensure that it is permissible to be connected to the facilities of the local telecommunications company. [. . . ]