User manual SONY VAIO VPC-CW2RGX/B

[. . . ] Each of these displays requires a compatible inverter and display cable; the inverters, display cables, and displays are not interchangeable. Before ordering a replacement display, display cable, or inverter, refer to the display matrix. Basics Displays - 3 Displays Each of the four displays requires a compatible inverter and display cable. Refer to the following pages to identify the displays. Basics Displays - 4 Active-Matrix Display The active-matrix display is available for the PowerBook 170 only. Use the following replacement parts with the PowerBook 170: · Active Matrix Display 661-0711 · Inverter (green) 699-0273 · Display Cable 630-6273 · Inverter Cable 936-0106 Basics Displays - 5 FSTN Display, Rev. [. . . ] Remove the five torx screws from the bottom case. Take Apart 2 Top Case - 9 Lift up the top case and disconnect the interconnect cable. Interconnect Ribbon Cable 3 Lift off the top case and unhook the two tab fasteners from the front of the bottom case. Replacement Caution: When connecting the interconnect cable, fold the cable as shown. If it is not folded correctly, the cable could short. Tab Fastener Take Apart Hard Drive - 10 Hard Drive Before you begin, remove the following: · Main battery · I/O door · Top case · Modem card (if present) Caution: The PowerBook140/145/170 contains CMOS devices that are very susceptible to ESD damage. To prevent damage, wear a grounding wriststrap. Review the ESD precautions in Bulletins/ Safety. Hard Drive Take Apart 1 Hard Drive - 11 Caution: The hard drive ribbon cable is fragile. Lift the locking tab on connector J11 and remove the hard drive ribbon cable from the motherboard. Locking Tab J11 Connector Take Apart 2 Hard Drive - 12 Using a T-8 torx driver, remove the five screws from the drive retainer. 3 Using a jeweler's screwdriver, release the drive retainer latch and remove the retainer. Take Apart 4 5 Hard Drive - 13 Lift the hard drive out of the bottom case. Note: If the hard drive does not have a release tab, carefully pry the cable from the drive with a screwdriver. Release Tab Pull the release tab and disconnect the hard drive cable. Take Apart Hard Drive - 14 Replacement Note: Drive retainers for 17-mm-high and 19-mm-high hard drives are not interchangeable. Check the height of the replacement drive and use the appropriate drive retainer. For hard drive upgrades, refer to Upgrades. Replacement Note: For information on returning drives, cables, and carriers to Apple, refer to Additional Procedures in the Hard Drives manual. Take Apart Floppy Drive - 15 Floppy Drive Before you begin, remove the following: · Main battery · I/O door · Top case · Modem card (if present) Caution: The PowerBook 140/145/170 contains CMOS devices that are very susceptible to ESD damage. To prevent damage, wear a grounding wriststrap. Review the ESD precautions in Bulletins/Safety. Floppy Drive Take Apart 1 Floppy Drive - 16 Caution: The floppy drive ribbon cable is fragile and should be handled with care. Pull up and rotate the actuator toward the display to remove it from the top case. Take Apart Elevation Feet - 36 Elevation Feet Before you begin, remove the following: · Main battery · I/O door · Top case Elevation Foot Caution: The PowerBook 140/145/170 contains CMOS devices that are very susceptible to ESD damage. To prevent damage, wear a grounding wriststrap. Review the ESD precautions in Bulletins/Safety. Elevation Foot Take Apart 1 Elevation Feet - 37 Using a T-8 torx driver, remove the torx screw and washer and the spring clip from the inside of the elevation foot. Pull off the elevation foot. Spring Clip 2 Elevation Foot Take Apart Daughterboard - 38 Daughterboard Before you begin, remove the following: · Main battery · I/O door · Top case · RAM expansion card (if present) Daughterboard Take Apart Daughterboard Motherboard Daughterboard - 39 Caution: The PowerBook 140/145/170 contains CMOS devices that are very susceptible to ESD damage. To prevent damage, wear a grounding wriststrap. Review the ESD precautions in Bulletins/Safety. 1 Using a T-8 torx driver, remove the four daughterboard mounting screws. Logic Board Take-Apart Tool Caution: Always use the logic board take-apart tool to separate the daughterboard connector from the motherboard Take Apart Daughterboard - 40 connector. Trying to disconnect the daughterboard from the motherboard by rocking or peeling the boards apart damages the connectors. 2 Using the logic board take-apart tool, disconnect the daughterboard from the motherboard. Note: For tools ordering information, refer to "Special Tools" in Bulletins/Service Notices. Take Apart Motherboard - 41 Motherboard Before you begin, remove the following: · Main battery · I/O door · Top case · RAM expansion card (if present) · Daughterboard · Modem board (if present) Motherboard Take Apart Floppy Drive Cable Thermistor Cable Hard Drive Cable Motherboard - 42 Caution: The PowerBook 140/145/170 contains CMOS devices that are very susceptible to ESD damage. To prevent damage, wear a grounding wriststrap. Review the ESD precautions in Bulletins/Safety. [. . . ] Using a T-8 torx driver, remove the four display mounting screws. Display 6 Additional Procedures 7 Shim Installation - 20 Remove the display from the EMI shield and housing. Place the display face-down on the keyboard. Additional Procedures Shim Installation - 21 Note: The PowerBook 145 display is shown. 8 Locking Tab Lift the locking tab on the display connector and disconnect the display cable. (Back of Display Shown) Additional Procedures Shim Shim Installation - 22 9 Remove the clear shim from its paper backing. Cable 10 Turn back the display cable and press the shim onto the back (the nonconductive side) of the display cable connector. Make sure that the shim is unwrinkled and flush with the edges of the cable and that it does not cover the connector traces. [. . . ]