User manual SONY VAIO VPC-EB26GX/BI

[. . . ] The computer and any attached peripherals are turned off and the peripherals are disconnected from the input/output (I/O) panel. You can replace or reinstall a part by performing the removal procedure in reverse order unless additional information is provided. q file:///c|/docs/blanco E-doc/removing. htm (1 of 29) [9/1/2000 3:31:59 PM] Removing and Replacing Parts: Dell Inspiron 5000 Series Precautionary Measures NOTICE: Only a certified service technician should perform repairs on your computer. Damage or inoperability due to servicing not authorized by Dell is not covered by your warranty. WARNING: FOR YOUR PERSONAL SAFETY AND PROTECTION OF THE EQUIPMENT: Before you start to work on the computer, perform the following steps in the sequence indicated: 1. Ground yourself by attaching an antistatic grounding strap to your wrist and to an unpainted metal surface on the computer I/O panel. [. . . ] Some of the interface connectors are zero insertion force (ZIF) connectors. These connectors are not removable; they must be released to disconnect a cable from them. To disconnect a cable from a ZIF connector, perform the following steps: 1. Insert a small flat-blade screwdriver, dental pick, or fingernail under the movable part of the connector. Pull up gently on the movable part of the connector until the cable is released. Some ZIF connectors may need to be lifted in the center. Grasp the cable and pull it out of the connector. To reconnect an interface cable to a ZIF connector, perform the following steps: 1. Insert the end of the cable into the connector. While holding the cable in place, close the ZIF connector. To ensure a firm connection, make sure the ZIF connector is completely closed. Modem Removal NOTICE: Only a certified service technician should perform repairs on your computer. Failure to do so may cause the connector to become disengaged as a result of shock or vibration to the computer. Processor Module Removal NOTICE: Only a certified service technician should perform repairs on your computer. Damage or inoperability due to servicing not authorized by Dell is not covered by your warranty. Inspiron 5000 computers have 3 screws (first photo), and Inspiron 5000e computers have 2 screws (second photo). file:///c|/docs/blanco E-doc/removing. htm (13 of 29) [9/1/2000 3:32:00 PM] Removing and Replacing Parts: Dell Inspiron 5000 Series 2. When you replace the processor, be sure to attach it to the connector. file:///c|/docs/blanco E-doc/removing. htm (14 of 29) [9/1/2000 3:32:00 PM] Removing and Replacing Parts: Dell Inspiron 5000 Series When you replace the processor during reassembly, be sure to attach it to the connector. LCD Removal NOTICE: Only a certified service technician should perform repairs on your computer. Damage or inoperability due to servicing not authorized by Dell is not covered by your warranty. Open the display and disconnect the LCD flex cable. Close the display and remove the four LCD hinge screws. NOTICE: Route the cable under the cable clip on computers that have extended cable clips so that the LCD flex cable will stay connected to the system board. Video Board Removal NOTICE: Only a certified service technician should perform repairs on your computer. Damage or inoperability due to servicing not authorized by Dell is not covered by your warranty. Disconnect the touch pad cable. file:///c|/docs/blanco E-doc/removing. htm (15 of 29) [9/1/2000 3:32:00 PM] Removing and Replacing Parts: Dell Inspiron 5000 Series Diskette Drive Removal NOTICE: Only a certified service technician should perform repairs on your computer. Damage or inoperability due to servicing not authorized by Dell is not covered by your warranty. [. . . ] Remove the two screws from each side of the panel. Disconnect the cold cathode fluorescent lamp (CCFL) cable from the bottom of the panel. Disconnect the flex cable from the back of the LCD panel. Lift the panel from the back cover. LED/Inverter Board Removal 1. [. . . ]