User manual SONY VPCEG24FX/P

[. . . ] • Do not place the device where it is always exposed to water. • Do not place the device where it is exposed to oil. • Construction work should be carried out in accordance with constructionrelated law and always by a professional constructor. If the device installation requires construction work, make sure to observe the following precautions. [. . . ] If there is reason to believe that condensation might have occurred, leave the device for several hours until the condensation has completely dried out. • Be sure to observe the amplifier’s rated load impedance (see SPECIFICATIONS), particularly when connecting speakers in parallel. Connecting an impedance load outside the amplifier’s rated range can damage the amplifier. • When connecting the speakers with high impedance, be sure that the output total of each speaker does not exceed the rated output of the power amplifier. • ABOUT THE PROTECTION CIRCUIT This speaker system has an internal protection circuit that shuts off the speaker unit when an excessive input signal is applied. If the speaker unit emits no sound, reduce the volume level of the amplifier immediately. The sound will return automatically in several seconds. • Place the speaker on a flat and smooth surface. • Do not place the speaker on the ground with the grille faced down. • Do not touch the speaker driver unit. LF HF Coverage angle (500 Hz – 4 kHz on average) Nominal impedance Power rating NOISE (IEC, 100h) *1 PGM MAX Sensitivity (1W, 1m) *2 Maximum SPL (Calculated, 1m) *3 Frequency range (-10 dB) *2, *4 Crossover frequency Connector Transformer taps 70 V 100 V Overload protection Magnetically shielded Dust and water resistant *5 Enclosure Shape Cabinet material Baffle material Grille material Finish Dimensions (Speaker only) (W × H × D in vertical cabinet orientation) Net weight (Speaker only, 1 piece) Packaging Connections • Before connecting the device to a power amplifier, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. The 8Ω position should be selected for 8Ω audio systems only. If the setting is incorrect, it may cause malfunction of the speaker and amplifier. • Make sure the amplifier is switched off before operating the tap selector switch. NOTE The safety pin can be attached from either side of the mounting bracket depending on the angle of the speaker. 3 Plug the Euroblock connector into the socket in the speaker. 4 ATTACH THE MOUNTING BRACKET AND SAFETY WIRE Euroblock connector 1 Attach the mounting bracket and safety wire to the speaker. Use the supplied screws to attach the mounting bracket. The way to attach the mounting bracket depends on the orientation of the speaker (vertical or horizontal). Vertical installation Mounting bracket NOTE Use a flat-blade screwdriver with a blade less than 3 mm (0. 1 in. ). Less than 3 mm (0. 1 in. ) There are two acceptable wiring methods. Vertical CAUTION When connecting with low impedance, take note of the combined resistance. Using Loop-Through Terminals For this method, cables are connected from terminals 1 and 4 to the subsequent speaker. If the Euroblock connector is disconnected from a speaker, all subsequent speakers will not work. This can be useful to identify which speaker has a problem. Angle adjustment bolt Safety wire Stopper screw (VXS8/VXS8W only) 4 Attach the terminal cover. Terminal cover Horizontal installation Stopper screw (VXS8/VXS8W only) Angle adjustment bolt Horizontal From amplifier or previous speakers NOTE Mounting bracket can be attached in reverse direction. To subsequent speakers To subsequent speakers 5 (If installing the speaker to the wall) turn the speaker horizontally to set the angle. [. . . ] 3 Install the bracket base onto the wall/ceiling. Make sure to fasten four corners of the bracket base. 4 Pass cables through the gap at the lower part of the bracket cover, and put the bracket cover on the bracket base. NOTE If you want to adjust the slack of cables last, the bracket cover can be attached after step 5-6. Bracket base Euroblock connector Power amplifier Speaker Bracket cover Power amplifier Euroblock connector Bolt with hexagon hole Speaker 5 INSTALL THE SPEAKER TO THE BRACKET BASE AND FIX THE CABLE 1 Install the mounting bracket to the bracket base. [. . . ]