User manual SONY VPCEG25FX/L

[. . . ] http://www. yamahaproaudio. com/ Notices • The Wireless DCP application and this manual are copyright of Yamaha Corporation. • Copying of the Wireless DCP application or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of Yamaha Corporation. • Yamaha Corporation makes no representations or warranties with regard to the use of the Wireless DCP application and this manual and cannot be held responsible for the results of usage thereof. • Screen displays as illustrated in this manual are for instructional purposes and may appear somewhat different from those on your smart device. [. . . ] Press the Home button to complete the network setting process. Wireless DCP Owner’s Manual 7 3. Configuration  Key points for network configuration Smart device MTX processor Wi-Fi access point Computer 1. All of the devices to be connected—that is, the MTX processor, the Wi-Fi access point, the smart device, and the computer running MTX Editor—must have IP addresses from the same network (or subnet). If, for example, the subnet mask is 255. 255. 255. 0 and the MTX processor’s IP address is 192. 168. 0. 1, the smart device should have an IP address in the form of 192. 168. 0. xx. Good combination of settings Router with integrated Wi-Fi* and DNS MTX processor Smart device Computer 192. 168. 0. 100 192. 168. 0. 1 192. 168. 0. 101 192. 168. 0. 253 Incorrect combination of settings 192. 168. 11. 1 192. 168. 0. 1 192. 168. 11. 50 192. 168. 0. 253 *: If using a Wi-Fi access point that is not also a router, set the IP address for accessing it. 2. If the Wi-Fi access point’s DHCP server automatically assigns IP addresses, be sure that any IP addresses set statically for other devices are not duplicated. We recommend that you check the setting for the range of IP addresses that can be assigned automatically. Meanwhile, if the Wi-Fi access point’s default IP subnet is not the same as that of the MTX processor, an incorrect combination of settings (similar to that shown in 1. above) will result and normal operation will not be possible. Because the IP subnet automatically assigned to the smart device in such a case will also differ from that of the MTX processor, it will not be possible to connect. Two smart devices running Wireless DCP can be connected to each MTX processor. (However, only one device can be logged into by an administrator password. ) 4. As shown below, certain functions are available only when logged into the MTX processor using an administrator password. Administrator Select Page Change Password Edit Staff Pages    Staff  (but restricted by administrator) × × NOTE You can restrict the functions for staff use by assigning different passwords for administrator and staff. Wireless DCP Owner’s Manual 14 3. Configuration  To reset a password 1. Tap Reset to display the Reset Password screen. If, for example, you forget a password, you can use this screen to reset (or remove) it. Note that both administrator and staff passwords are reset by this action. Tap the MAC address field to display the onscreen keyboard. Enter the MAC address of the MTX processor to connect using the keyboard. You can check the MAC address from the MTX Editor. Wireless DCP Owner’s Manual 15 3. You will be asked to confirm that you wish to reset the passwords. Tap Yes to do so. Wireless DCP Owner’s Manual 16 4. Controller Screen The Controller screen is used to remotely control the connected MTX processor. Controller pane This pane contains switches and faders configured and arranged using MTX Editor. Information displayed Upper line: Name of connected device Lower line: Page name Page button Tap to display the Select Page screen. Controller 1 and Controller 2 buttons Tap to switch the Controller pane’s display. Settings button Tap to display the Settings screen. [. . . ] Getting Started and Section 3. 2 iOS Device. You should also ensure that the IP addresses of the router and DNS have been set as connection will be periodically lost if it is not.  Failed to establish connection The error message on the left may be displayed as a result of incorrect network settings on the smart device. Ensure that the MTX processor’s network settings match those in Wireless DCP. For details regarding these settings, refer to Section 3. 1 MTX Processor Network and Section 3. 2 iOS Device. [. . . ]