User manual SONY VPCEG26FX/B

[. . . ] You may need them when maintaining or moving this unit. ) Model number suffix “EB” denotes UK model. EB until 2013/1/17 VQT4U45 SC-NE1_EB~VQT4U45. book 2 ページ ２０１３年１月１５日　火曜日　午後８時２０分 Caution for AC Mains Lead (For the AC mains plug of three pins) For your safety, please read the following text carefully. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark Ï or the BSI mark Ì on the body of the fuse. [. . . ] ≥ For further support on your product, please visit our website: www. panasonic. co. uk Direct Sales at Panasonic UK ≥ Order accessory and consumable items for your product with ease and confidence by phoning our Customer Communications Centre Monday–Friday 9:00 am – 5:00 pm (Excluding public holidays). ≥ Or go on line through our Internet Accessory ordering application at www. pas-europe. com. ≥ Most major credit and debit cards accepted. ≥ All enquiries transactions and distribution facilities are provided directly by Panasonic UK. ≥ Also available through our Internet is direct shopping for a wide range of finished products. Take a browse on our website for further details. ∫ Range of use ≥ Use this device at a maximum range of 10 m. The range can decrease depending on the environment, obstacles or interference. ∫ Interference from other devices ≥ This unit may not function properly and troubles such as noise and sound jumps may arise due to radio wave interference if this unit is located too close to other Bluetooth® devices or the devices that use the 2. 4 GHz band. ≥ This unit may not function properly if radio waves from a nearby broadcasting station, etc. is too strong. ∫ Intended usage ≥ This unit is for normal, general use only. ≥ Do not use this system near an equipment or in an environment that is sensitive to radio frequency interference (example: airports, hospitals, laboratories, etc). 4 VQT4U45 SC-NE1_EB~VQT4U45. book 5 ページ ２０１３年１月１５日　火曜日　午後８時２０分 Control reference guide Top view 1 − VOLUME ＋ SOUND 2 1 4 9 10 11  OK  4 PLAY MENU 5 SETUP 3 5 6 7 8 1 Standby/on switch [Í/I] ([Í]) Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. ∫ Before using for the first time Remove the insulation sheet A. 2 3 4 5 6 7 Enter sound menu Enter setup menu Select Bluetooth®/AUX Adjust the volume (0 (min) to 50 (max)) Enter the Bluetooth® menu/ Change the sound input level of the external device (l 6) Mute the sound Mutes the sound. If a 9th device is paired, the device that has not been used for the longest time will be replaced. Bluetooth® input level If the sound input level of the Bluetooth® transmission is too low, change the input level setting. Preparation ≥ Connect a Bluetooth® device. Connecting a paired Bluetooth® device Preparation ≥ Turn on the Bluetooth® feature of the device and place the device near this unit. ≥ If this unit is already connected to a Bluetooth® device, disconnect it. 1 2 Press [PLAY MENU] repeatedly to select “INPUT LEVEL”. Press [3, 4] to select the level and then press [OK]. Press [3, 4] to set the time (in minutes) and then press [OK]. “SLEEP 30” , . “SLEEP 120” ^---------------------. “OFF” (Cancel) (----------------------J 1 2 3 Press [ , AUX] to select “AUX”. ≥ The remaining time is indicated on the unit’s display except when other operations are performed. While pressing and holding [ / AUX] on the unit, press and hold [SOUND] on the remote control until the unit’s display shows “REMOTE 2”. Press and hold [OK] and [SOUND] on the remote control for at least 4 seconds. Display brightness The brightness of this unit’s display can be changed. 1 2 Press [SETUP] repeatedly to select “DIMMER”. Press [3, 4] to select “ON” and then press [OK]. ≥ To change the mode back to “REMOTE 1”, repeat the steps above but replace the button pressed on the remote control from [SOUND] to [ , AUX]. ≥ To cancel the dimmer, select “OFF” in step 2. Automatic standby As a factory preset, this unit will always turn off automatically if there is no sound output and no operation for approx. To cancel this function 1 2 Press [SETUP] repeatedly to select “AUTO OFF”. Press [3, 4] to select “OFF” and then press [OK]. ≥ To turn automatic standby on, select “ON” in step 2. [. . . ] ≥ Refer to step 2 of “Wall mount instructions” for details about the required screws. ≥ Be sure to attach the fall prevention cord as a secondary safety measure. Installation accessories ∫ Supplied accessories ≥ 1 Safety holder ≥ 1 Screw ≥ 2 Wall mount brackets Wall mount instructions Before installation, turn the unit off and disconnect the AC mains lead from the mains socket. ∫ Additionally required accessories (commercially available) ≥ 4 Wall mount bracket fixing screws ≥ 1 Safety holder fixing screw ≥ 1 Fall prevention cord* ≥ 1 Screw eye * Use a cord that is capable of supporting over 33 kg (with a diameter of about 1. 5 mm). ≥ Keep the safety holder out of reach of children to prevent swallowing. ≥ Keep the screws out of reach of children to prevent swallowing. [. . . ]