User manual SONY VAIO VPCSB4DFX/B

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. [. . . ] 625: Lights up when the unit is set up in the 625 standard. To select the broadcasting standard, select "03: VIDEO STD" in the menu. For more information, see "Menu Setup" (page 10). 6 8 FREQ BW (frequency bandwidth) indicators 36M: Lights up when the frequency bandwidth is 36 MHz. 18M: Lights up when the frequency bandwidth is 18 MHz. To select the frequency bandwidth, select "11: FREQ BW" in the menu. For more information, see "Menu Setup" (page 10). !¢ ITEM Â/µ buttons Select the menu item when the menu is displayed in the display window. Cursor (4/$/"/") buttons Use the 4 or $ button to change the parameters. Use the " or " button to move a digit to the left or right. !§ RESET button Resets the unit to the status present when the power has been turned on. Use a sharp-pointed object to press this button. 9 FEC RATE (Forward Error Correction rate) indicators 7/8: Lights up when the FEC rate is 7/8. 3/4: Lights up when the FEC rate is 3/4. To select the FEC rate, select "12: FEC RATE" in the menu. For more information, see "Menu Setup" (page 10). !º ALARM indicator When a fault is detected while the unit is in operation, the ALARM indicator lights up. In this case, a warning message (0X WARNING) appears in the display window. The back lighting for the MENU button turns off, and the unit exits the menu. 2 3 Select a menu item to be changed using the ITEM Â or µ button. Change the parameters using the 4 or $ button. Use the " or " button to move a digit to the left or right. 10 Saving the Parameters in Menu Banks Menu banks are provided with the unit as well as the current bank. The menu banks can store the 8 sets of parameters saved in the current bank. Follow the procedure below to save the set of parameters in menu banks. Recalling the Parameters from Menu Banks Follow the procedure below to recall the set of parameters from the menu banks. 1, 5 INPUT SEL ALOG SDI AUDIO SDI AEB/EBU REF IN1 IN2 VIDEO STD EXT 525 625 FREQ BW 36M 18M FEC RATE 7/8 ENTER 3/4 ALARM MENU ITEM 2 RESET 1, 5 INPUT SEL ALOG SDI AUDIO SDI AEB/EBU REF IN1 IN2 VIDEO STD EXT 525 625 FREQ BW 36M 18M FEC RATE 7/8 ENTER 3/4 ALARM MENU ITEM 2 RESET 4 1 Press the MENU button. 3 4 1 Press the MENU button. 3 The back lighting for the MENU button lights up, and the menu appears in the display window. The back lighting for the MENU button lights up, and the menu appears in the display window. 2 3 4 Select "92: RECALL BANK" using the ITEM Â or µ button. Select the number of the desired menu bank to recall the contents into the current bank using the 4 or $ button. The contents of the selected menu bank are recalled to the current bank. To cancel recalling from the menu bank Press the MENU, ITEM Â or µ button before pressing the ENTER button. 2 3 4 Select "91: SAVE BANK" using the ITEM Â or µ button. Select the number of the menu bank in which the contents of the current bank to be saved using the 4 or $ button. The contents of the current bank are saved in the selected menu bank. The contents of the menu bank are saved even after the power is turned off. [. . . ] SDI: Digital audio signals in SDI format AES/EBU: Digital audio signals in AES/EBU format Turns the audio emphasis function on or off if the BKSM-T103 Analog Input Board is installed in the IN2 section of the unit. Sets an address for the unit itself if the BKSM-T101 SDTI Input Board is installed in the IN2 section of the unit. When the address matches the destination address of the input signals, the unit receives them. Selects the audio input signal channels to the IF OUT connector when an optional board is installed in the IN2 section of the unit. [. . . ]