User manual SONY VPH-1271Q

[. . . ] 4 Control/Connector Panel . . . . . . . . . . . . . . 5 Remote Commander . . . . . . . . . . . . . . . . . . . . . 6 The Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 The Information Menu . . . . . . . . . . . . . . . . . . . . . 30 Maintenance Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . 34 Projecting the Picture Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . 8 Connecting the Projector . . . . . . . . . . . . . . . . . . . [. . . ] See the chart on page 42 to find if the signal is registered in the preset memory. Since the data for the following signals is recalled from the preset memory, you can use these preset data items by adjusting "H Size. " Make finer adjustments by adjusting "Shift. " Signal Super Mac-2 SGI-1 Macintosh 19" Macintosh 21" Sony News PC-9821 1280 × 1024 WS Sunmicro Note Memory No. SIZE 37 37 39 41 47 47 48 1312 1320 1328 1456 1708 1600 1664 When the aspect ratio of input signal is other than 4:3, a part of the screen is displayed in black. 24 The Signal Menu The Function Menu The Function menu is used for changing the settings of the projector. Setting items Smart APA Functions Initial setting The APA (Auto Pixel Alignment) automatically On adjusts "Dot Phase, " "H Size" and "Shift" on the Signal menu for the input signal from a computer. · On: When a signal is input from a computer, the APA functions automatically so that the picture can be seen clearly. Once the specified input signal has been adjusted by the "Smart APA, " it will not be readjusted even when the cable is disconnected and connected again or the input channel is changed. You can adjust the picture by pressing the APA key on the Remote Commander even if "Smart APA" set to "On. " · Off: The APA functions when you press the APA key on the Remote Commander. When set to "On, " the projector detects input signals in Off the following order: Input-A/Video/S-Video. It indicates the input channel when the INPUT key is pressed. When set to "Off, " the focus adjustment does not work On automatically when the projector is turned on or when the AUTO FOCUS key on the projector or the remote commander is pressed. When set to "On, " a test pattern is displayed on the screen during "Lens Zoom", "Lens Focus, " or "V Keystone" adjustment. When set to "Low", the power consumption is set to low in standby mode. Blue Adjustments and Settings Using a Menu Background Lamp Mode Standard Lens Control When set to "Off, " the LENS (FOCUS, ZOOM) key on the On Remote Commander, and the FOCUS and ZOOM keys on the projector do not function. Selects the remote control detectors (IR Receiver) on the front and rear of the projector. · Front & Rear: Activates both the front and rear detectors. · Front: Activates the front detector only. · Rear: Activates the rear detector only. Selects whether the SONY logo on the rear panel of the projector lights when the projector is on. Set to "On" when the projector is used at an altitude of 1, 500 m or higher. Front & Rear IR Receiver Illumination High Altitude Mode On Off The Installation Menu 27 Note The auto V Keystone adjustment may not correct the trapezoidal distortion perfectly, depending on the room temperature or the screen angle. 28 The Installation Menu The Setup Menu The Setup menu is used for changing the menu displays. Setting items Status (on-screen display) Functions Sets up the on-screen display. When set to "Off, " turns off the on-screen displays except for the menus, a message when the power is turned off, and warning messages. Selects the language used in the menu and on-screen displays. The languages available are: English, Nederlands, Français, Italiano, Deutsch, Español, Português, , Svenska, Norsk, , , , and . Initial setting On Language English Adjustments and Settings Using a Menu Auto Input-A Signal Sel. [. . . ] Otherwise, use a proper power cord meeting the following specifications. The United States, Canada Plug type Female end Cord type Rated Voltage & Current Safety approval Cord length (max. ) YP-11 YC-13L SPT-2 10A/125V UL/CSA 4. 5 m Continental Europe, Korea YP-21 YC-13L 2. 5A/250V VDE ­ UK Australia Japan SP-61 YC-13L 2. 5A/250V BS ­ B8 C7-2 2. 5A/250V SAA ­ YP-13 YC-13L 7A/125V DENAN ­ Others H03VVH2-F H03VVH2-F H03VVH2-F VCTFK Specifications 43 Index A Adjusting memory of the settings . . . . . . . . . . . . . . . . . . . . . . . . 21 the picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 the picture size/shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]