User manual SONY VPL-CX80

[. . . ] To prevent fire or shock hazard, do not expose the unit to rain or moisture. Telephone Number: 858-942-2230 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] You can switch the following functions of the Intelligent Auto-setup to manual adjustments using the menu. Make sure that nothing obstructs the infrared beam between the Remote Commander and the remote control detector on the projector. If you are leaving the conference room immediately, turn the projector off, and then, after the lens protector closes and the powered tilt adjuster is put away in the projector, you can unplug the AC power cord. After the AC power cord is unplugged, the fan runs automatically. When unplugging the AC power cord, ensure that the lens protector closes and the powered tilt adjuster is put away in the projector. Moving the projector with the powered tilt adjuster rised may damage the adjuster. Turn off the projector according to the procedure in "Turning off the power", then cool it down when storing the projector in the carrying case. Move the icon to the point on the image you want to enlarge. Use the arrow key (M/m/</, ) to move the icon. By pressing the + key repeatedly, the image size increases (ratio of enlargement: max. If you will be using a circuit breaker to turn the power for the entire system on and off, set the direct power on function to "On. " When you turn off the power, you can also just unplug the power cord without pressing the I / 1 key. The internal circuitry will cause the fan to automatically operate for a certain time even after the power cord is removed. However, if the unit has been on for less than 15 minutes, the fan might not begin to turn as a result of inadequate charging. In that case, follow the procedure for turning off the power as described in "Turning Off the Power" on page 22. Use the arrow key (M/m/</, ) to scroll the enlarged image. This function works when a signal from a computer is input. This function does not work when a video signal is input. To return the image back to its original size Press the D ZOOM ­ key. Just pressing the RESET key returns the image back to its original size immediately. "Freeze" appears when the key is pressed. This function works when a signal from a computer is input. [. . . ] ) Resolution 750 horizontal TV lines (Video input) 1, 024 × 768 dots (RGB input) Acceptable computer signals1) fH: 19 to 92 kHz fV: 48 to 92 Hz (Maximum input signal resolution: SXGA+ 1400 × 1050 fV: 60 Hz 1) Set the resolution and the frequency of the signal of the connected computer within the range of acceptable preset signals of the projector. 43 is the color system used when playing back a video 1 Vrms, when an input signal is 500 mVrms, impedance less than 5 kilohms REMOTE RS-232C: D-sub 9 pin Safety regulations UL60950, cUL (CSA No. 3 BTU Operating temperature 0°C to 35°C (32°F to 95°F) Operating humidity 35% to 85% (no condensation) Storage temperature ­20°C to 60°C (­4°F to 140°F) Storage humidity 10% to 90% Supplied accessories Remote Commander (1) Size AA (R6) batteries (2) HD D-sub 15 pin cable (2 m) (1) (1-791-992-21) USB cable A type - B type (1) (1-790-081-31) Carrying case (1) AC power cord (1) Air filter (for replacement) (1) Operating Instructions (1) Quick Reference Card (1) Security Label (1) Design and specifications are subject to change without notice. Projector Lamp LMP-C190 (for replacement) Signal Cable SMF-402 (HD D-sub 15-pin (male) y 3 × phono type (male)) Some of the items may not be available in some areas. [. . . ]