User manual SONY WAHT-SA2

[. . . ] Other versions may not comply with FCC technical regulations. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Hereby, Sony Corporation declares that this Equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. De/ This product is intended to be used in the following countries: GB, IE, IS, DE, CH, AT, LI, NL, LU, BE, FR, IT, MT, ES, PT, GR, CY, DK, SE, NO, FI, EE, LV, LT, PL, CZ, HU, SI, BG, RO, SK The WLAN feature of this Equipment shall exclusively be used inside buildings. Any use of the WLAN feature of this Equipment outside of the buildings is prohibited on the French territory. Please make sure that the WLAN feature of this Equipment is disabled before any use outside of the buildings. Use of the RLAN network is governed: ­ with respect to private use, by the Legislative Decree of 1. 105 indicates when free use is permitted; ­ with respect to the supply to the public of the RLAN access to telecom networks and services, by the Ministerial Decree of 28. 6A/2006 is the General Authorization for the use of Radiofrequencies by Radio Local area Networks and by Wireless Access Systems, including Radio Local Area Networks (WAS/ RLAN). The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Clean the cabinets only with a soft dry cloth. The Wireless Surround Speaker Kit (WAHT-SA2) includes two surround back speakers and a surround amplifier. By using this kit along with a Sony Home Theatre System, you can enjoy the more realistic surround sound effect of a 7. A Front left speaker B Front right speaker C Center speaker D Surround left speaker E Surround right speaker F Surround back left speaker G Surround back right speaker H Subwoofer I Surround amplifier (for surround speakers) J Surround amplifier (for surround back speakers) Before installing, make sure to remove the AC power cords (mains leads) of all S-AIR products from wall outlets (mains). For S-AIR main units that do not include a wireless transmitter, prepare the optional S-AIR Adapter (EZWT100). Not all S-AIR main units look exactly the same. Do not insert anything other than the wireless transceiver into the EZW-RT10 slot. Do not connect the speaker cords supplied with the Wireless Surround Speaker Kit to any of the speaker jacks on your S-AIR main unit. Before connecting the AC power cords (mains leads) of your S-AIR main unit and the surround amplifier to wall outlets (mains), make sure that all speakers are connected. X To connect the speaker cords to the speakers Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with the color tube to 3, and the speaker cord without the color tube to #. To use the wireless system, you need to set up the surround amplifier and your S-AIR main unit. Before setting, make sure that the wireless adapters are correctly inserted in the S-AIR main unit and surround amplifier(s). [. . . ] When sound transmission is established, the S-AIR/STANDBY indicator turns green and the PAIRING indicator turns on. If you use more than one surround amplifier, perform Steps 3 and 4 for those also. X After the pairing operation (example) Sound transmission is established between the surround amplifier and the S-AIR main unit that performed the pairing operation. To press PAIRING, a slim instrument, such as a paper clip, can be used. [. . . ]