User manual SONY WEGA KV-24FS120

[. . . ] Connecting Additional Equipment 4-101-452-21 Operating Instructions KV-20FS120 KV-24FS120 © 2004 by Sony Corporation User Guide Connecting Additional Equipment WARNING To reduce the risk of fire or electric shock, do not expose the TV to rain or moisture. To reduce the risk of electric shock, do not use this polarized plug with an extension cord, receptacle, or other outlet unless the blades can be fully inserted to prevent blade exposure. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. NOTIFICATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] You can use the button to switch between the VHF/UHF and VIDEO inputs. 10 TV, Satellite Receiver, and VCR Satellite antenna cable 4 From cable/ antenna Rear of TV 1 VCR 2 Connections Satellite Receiver 3 5 Video (yellow) Audio L (white) Audio R (red) 1 2 3 4 5 Connect the cable from your satellite antenna to SATELLITE IN on the satellite receiver. Connect the coaxial cable from your cable service or antenna to the IN jack on your VCR. Using a coaxial cable (not supplied), connect the OUT jack on your VCR to the VHF/UHF jack on your TV. Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your satellite receiver to AUDIO and VIDEO IN on your VCR. Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your VCR to AUDIO and VIDEO IN on your TV. Optional Connection To view from the satellite receiver or VCR, select the video input to which your satellite receiver or VCR is connected by pressing on the remote control. 11 Connecting a DVD Player using Composite Video (Video/Audio L(Mono), R) Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your DVD player to AUDIO/VIDEO IN on your TV. Rear of TV Rear of DVD Player Connections Optional connection Video (yellow) Audio L (white) Audio R (red) Optional connection For better picture quality, use S VIDEO instead of the yellow audio/video cable. S-VIDEO does not provide sound, so you still must connect the audio cables. If your DVD player is equipped with component video outputs (Y, PB, PR/L, R), you can improve the picture quality by using component video cables (480i only). Connecting a DVD Player using Component Video (Y, PB, PR) Rear of TV Rear of DVD Player PR (red) PB (blue) Y (green) Audio L (white) Audio R (red) 2 1 1 2 Using component video cables (not supplied), connect the Y, PB, PR OUT on your DVD player to Y, PB, PR IN on your TV. Connect AUDIO OUT on your DVD player to AUDIO IN on your TV. The Y, PB, PR outputs on your DVD player are sometimes labeled Y, CB, and CR or Y, B-Y, and R-Y. If so, connect the cables to like colors. 12 Connecting Headphones Connect the headphones to the jack on the front of your TV. Headphone jack is STEREO. Front A/V Panel Connections Connecting a Camcorder Using audio/video cables (not supplied), connect AUDIO and VIDEO OUT on your camcorder to AUDIO and VIDEO IN on your TV. Front A/V Panel A/V output Audio R (red) Audio L (white) Video (yellow) 13 Connecting for Video Tape Editing (VCR and Camcorder) Camcorder (for playback) 1b Rear of TV Connections A/V output VCR (for playback) Video (yellow) Audio L (white) Audio R (red) 1a VCR (for recording) 2 1 For video tape editing connect to the VCR the following sources (VCR or Camcorder): a) Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your first VCR to AUDIO/VIDEO IN on your second VCR b) Using audio/video cables (not supplied), connect the AUDIO/VIDEO OUT on your Camcorder to the AUDIO/VIDEO IN on your second VCR 2 Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on the second VCR to the AUDIO/VIDEO IN on your TV. 14 Using Basic Functions Setting Up the TV After you have finished connecting your TV, you can use Auto Program to set up your channels. During Auto Program, the TV will automatically search for available channels and program receivable channels. 1 When you start Auto Program wait until it is finished; otherwise it will skip over channels that are available. Perform Auto Program again to program receivable channels. Press to turn on the TV. The Initial Setup screen appears. Initial Setup Basic Functions First please connect cable/antenna Auto Program [CH+] [CH­] Exit 2 Press on the remote control or on the TV front panel to start Auto Program, or press to exit. The Initial Setup screen appears each time you turn on the TV until you perform Auto Program. 1 2 3 4 5 6 1 2 3 4 To perform Auto Program again Press . Press Press F or f to highlight On or Off according to how you connected your TV. Press After Auto Program finishes, press to search for channels. to exit. To reset the TV to factory settings Turn the TV on. Press and release the POWER button on the TV front panel. The TV will turn itself off, then back on. Release . 15 Quick Start to the Menus The following settings are available in your on-screen menus: Menu Allows you to Video: Vivid Picture Brightness Color Hue Sharpness Video Mode : Vivid Picture Controls Color Temp. : Cool VM : High Move Select End Return Select End Make adjustments to your picture settings. Basic Functions Audio Treble Bass Balance Steady Sound: Off Effect : Off MTS : Stereo Move Select End Change your audio settings. Channel Setup Favorite Channels Cable : On Channel Fix : Off Auto Program Channel Skip/Add Channel Label Move Select End Customize your channel settings. Parental Control Password : Move Select End Set rating limits on your TV based on a program's rating or content. 16 Menu Allows you to Timer Timer 1 : Set Timer 2 : Set Current Time Move Select End Set the clock on your TV and program scheduled viewing using Timer 1 and Timer 2. Setup Caption Vision : Off Info Banner : Off Video Label Tilt Correction Language : English 16:9 Enhanced: Off Move Select End Select closed captioning options, label video inputs, adjust tilt correction, select menu languages, or run a demo of the menus. Basic Functions 17 Using the Menus This section shows the options available for setting up and adjusting your TV. Using the Remote Control to Navigate on the On-Screen Menus PICTURE MODE VOL CH Move MENU Select RESET SLEEP RM-Y194 To navigate on the on-screen menus, use the "arrow" buttons (F , f , G , g) to move the cursor. Pressing these arrows will cause the cursor to move in the corresponding direction. [. . . ] Check the TV/VIDEO setting: when watching TV, set it to TV; when watching video equipment, set it to VIDEO 1, 2 or 3 (page 3). Try another channel to rule out station trouble. Adjust the Picture setting in the Video menu (page 20). Adjust the Brightness setting in the Video menu (page 20). [. . . ]