User manual SONY WEGA KV-32FS120

[. . . ] Connecting Additional Equipment 4-101-940-21 (1) Operating Instructions KV-32FS120 KV-36FS120 © 2004 by Sony Corporation User Guide Connecting Additional Equipment WARNING To reduce the risk of fire or electric shock, do not expose the TV to rain or moisture. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. NOTIFICATION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. [. . . ] Connect the single input jack of the splitter (not supplied) to your incoming cable/antenna (optional connection to view local channels or broadcast). Using coaxial cables (not supplied), connect the two output jacks of the splitter (not supplied) to: a) the IN jack on your satellite receiver b) the VHF/UHF jack on the TV Using a coaxial cable (not supplied), connect the OUT jack on your satellite receiver to the VHF/UHF IN on your VCR. Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your VCR to AUDIO/VIDEO IN on your TV. Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your satellite receiver to AUDIO/VIDEO IN on your TV. 4 5 6 16 Using your TV with this connection Program your Sony remote control to operate your VCR or satellite receiver (see page 5). To activate your remote, press (FUNCTION button) to operate your VCR or (FUNCTION button) to operate your satellite receiver. Press repeatedly to switch between VCR input (VIDEO input), VHF/UHF (local channels or unscrambled), or your cable box (cable system or scrambled channels). Connections 17 Connecting a TV, VCR, and Satellite Receiver using Component Video (Y, PB, PR) Rear of TV 4 1 Satellite Receiver LINE IN VIDEO AUDIO L AUDIO R L From 2 cable/ 1 S VIDEO 3 4 Y antenna VIDEO L (MONO) PB AUDIO OUT (VAR/FIX) PR VCR L L (MONO) Connections 3 Video (yellow) Audio L (white) Audio R (red) R R R Y VIDEO 1 PB L PR R R LINE OUT Y (green) PB (blue) PR (red) 6 7 Audio R (red) Audio L (white) 5 1 2 3 4 5 6 7 Connect the coaxial cable from your satellite antenna to SATELLITE IN on the satellite receiver. Connect the coaxial cable from your cable service or antenna to the IN jack on your VCR. Using a coaxial cables (not supplied), connect the OUT jack on your VCR to the VHF/UHF jack on your TV. Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your satellite receiver to AUDIO/VIDEO IN on your VCR. Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your VCR to AUDIO/VIDEO IN on your TV. Using component video cables (not supplied), connect Y, PB, PR OUT on your satellite receiver to Y, PB, PR IN on your TV. Connect AUDIO OUT on your satellite receiver to AUDIO IN on your TV. Using your TV with this connection Program your Sony remote control to operate your VCR or satellite receiver (see page 5). Turn on your VCR to enable your satellite receiver to work with this connection. To activate your remote, press (FUNCTION button) to operate your VCR or (FUNCTION button) to operate your satellite receiver. Press repeatedly to switch between VCR input (VIDEO input), VHF/UHF (local channels or unscrambled), or your cable box (cable system or scrambled channels). 18 Connecting a DVD Player using Composite Video (VIDEO/AUDIO L(MONO), R) Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your DVD player to AUDIO/VIDEO IN on your TV. Rear of TV Rear of DVD Player 1 S VIDEO Y 3 4 PB AUDIO OUT (VAR/FIX) PR VIDEO L (MONO) L L (MONO) R R R Connections Optional connection Audio R (red) Audio L (white) Video (yellow) Optional connection For better picture quality, use S VIDEO instead of the yellow video cable. S VIDEO does not provide sound, so you still must connect the audio cables. Connecting a DVD Player using Component Video (Y, PB, PR/R, L) If your DVD player is equipped with component video outputs (Y, PB, PR), you can improve the picture quality by using component video cables (480i only). Rear of TV Rear of DVD Player 1 S VIDEO Y 3 4 PB AUDIO OUT (VAR/FIX) PR VIDEO L (MONO) L L (MONO) R R R PR (red) PB (blue) Y (green) Audio L (white) Audio R (red) 2 1 1 2 Make sure your DVD player is set up (See page 41). Using component video cables (not supplied), connect Y, PB, PR OUT on your DVD player to Y, PB, PR IN on your TV. Connect AUDIO OUT on your DVD player to AUDIO IN on your TV. The Y, PB, PR outputs on your DVD player are sometimes labeled Y, CB, and CR or Y, B-Y, and R-Y. If so, connect the cables to like colors. Using your TV with this connection Program your Sony remote control to operate your DVD (see page 5). To activate your remote, press (FUNCTION button) to operate your DVD. [. . . ] Try another channel to rule out station trouble. Adjust the Picture setting in the Video menu (page 28). Adjust the Brightness setting in the Video menu (page 28). Check the antenna and/or cable connections (page 10). [. . . ]