User manual SONY WLA-NWB1K

[. . . ] 3-196-849-13 (1) BluetoothTM Audio Kit Operating Instructions WLA-NWB1K © 2007 Sony Corporation WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventilation of the apparatus with newspapers, tablecloths, curtains, etc. [. . . ] To enter "Pairing in process, " you need to turn off the power of the transmitter first. When not completed pairing Repeat the procedure from step 2. To quit "Pairing in process" Press and hold the power button of the transmitter for about 2 seconds to turn off the transmitter. ip T When pairing the transmitter with a number of Bluetooth receiving devices, repeat steps 2 to 5 for each device individually. 1 Notes Depending on the Bluetooth receiving device, the transmitter may not enter "Connectable" automatically. In this case, see the operating instructions supplied with the device. For using the Bluetooth function, it is required that the Bluetooth device on the other side is corresponding with the same profile as the transmitter. However, even if it is corresponding with the same profile, functions may differ depending on the specification of the Bluetooth device. Remote control for the Bluetooth receiving device by the Walkman. You can control the Bluetooth receiving device using the control button of the Walkman. Notes Remote control (Vol +/­, etc. ) Speaker with AVRCP When operating the Walkman as the Bluetooth receiving devices remote control, point the transmitter toward the Bluetooth receiving device. You may not be able to change the volume by the remote control from the Walkman depending on your Bluetooth receiving device. Point the transmitter toward the Bluetooth receiving device. 1 Pairing headset with other Bluetooth transmitting devices 1 2 Place the Bluetooth transmitting device to be paired together within 1 m of the headset. Press and hold the POWER button of the headset for about 7 seconds or more to enter "Pairing in process. " 3 Release the POWER button when the headset indicator starts flashing quickly. The headset enters the pairing process. Turning Bluetooth transmitting device to pairing standby mode. (See the operating instructions supplied with the Bluetooth transmitting device. ) The list of detected devices appears on the display of the Bluetooth transmitting device. The headset is displayed as "DR-BT21G. " This headset indicator status will vary as follows, and pairing is established with the Bluetooth transmitting device. The headset indicator flashes quickly: Pairing in process The headset indicator flashes when responding to the Bluetooth transmitting device: Pairing successful The headset indicator flashes (at about 5-second intervals): Connectable Passcode* of the headset is fixed at "0000. " Depending on the Bluetooth receiving device, it may be necessary to input the passcode (in this case, "0000"). The headset cannot be paired with a Bluetooth receiving device whose passcode is not "0000. " Note 20 * Passcode may be called "Passkey, " "PIN code, " "PIN number, " or "Password. " When not completed pairing Repeat the procedure from step 2. To quit "Pairing in process" Press and hold the power button of the transmitter for about 2 seconds to turn off the transmitter. Note For using the Bluetooth function, it is required that the Bluetooth device on the other side is corresponding with the same profile as the headset. However, even if it is corresponding with the same profile, the function may differ depending on the specification of the Bluetooth device. 21 Re-pairing the transmitter and the headset 1 2 3 4 Connect the transmitter to the Walkman (page 13). The power of the transmitter turns on. Press and hold the power button of the transmitter for about 2 seconds to turn it off. Place the transmitter and the headset to be paired together within 1 m. Press and hold the POWER button of the headset for more than about 7 seconds to enter "Pairing in process. " After about 3 seconds, the headset indicator (red) and the headset indicator (blue) will flash twice, but keep pressing the POWER button. 5 Release the POWER button when the headset indicator starts flashing quickly. The headset enters the pairing process. Press and hold the power button of the transmitter for about 7 seconds or more to enter "Pairing in process. " After about 2 seconds, the transmitter indicator will flash twice, but keep pressing the power button. Notes 22 "Pairing in process" is released after about 5 minutes. If pairing is not established within about 5 minutes, repeat the above procedure from step 1. To enter "Pairing in process, " you need to turn off the power of the transmitter first. Calling with headset Preparation for calling (Bluetooth connection) Check the following before operating the headset. ­ The Bluetooth function is active on the mobile phone. ­ Pairing of the headset and the Bluetooth mobile phone is complete. Headset indicator (red) VOL ­ button VOL + button Multi function button POWER button Headset indicator (blue) 1 Press and hold the POWER button for about 3 seconds while the headset is turned off. The headset indicator (blue) and headset indicator (red) flash together twice, the headset turns on and then the headset tries to connect to the last Bluetooth mobile phone that was used. Note Do not press and hold the POWER button for more than 7 seconds, otherwise pairing mode is entered. Tip The headset will stop trying to connect to the Bluetooth mobile phone after 1 minute. In such a case, press the multi function button to try to connect again. To adjust the volume Tips Press the VOL or ­ button. You cannot adjust the volume when not communicating. Volume level for calling and listening to music can be set independently. 2 To receive a call When an incoming call arrives, a ring tone will be heard from the headset. 1 Press the multi function button on the headset. ­ ring tone set on the headset ­ ring tone set on the mobile phone ­ ring tone set on the mobile phone only for Bluetooth connection The ring tone differs in the following ways, depending on your mobile phone. Note If you received a call by pressing the button on the Bluetooth mobile phone, some Bluetooth mobile phones may have handset use priority. In this case, set to talk with the headset by pressing and holding the multi function button for about 2 seconds, or by operating the Bluetooth mobile phone. For details, refer to the manual supplied with your Bluetooth mobile phone. To call 1 Use the buttons on your mobile phone when making a call. If no dial tone is heard on the headset, press and hold the multi function button for about 2 seconds. Tip You can call in the following way, depending on the Bluetooth mobile phone. Refer to the manual supplied with your mobile phone on operating details. [. . . ] Pairing information is not deleted by this operation. Insert a small pin, etc. , into the hole at a slight angle, and push until you feel a click. The headset does not operate properly. Pairing cannot be established. Locate the transmitter and the headset as near as possible. Check if you input correct passcode of the transmitter (page 17). [. . . ]