User manual SONY XA-NV100T READ THIS FIRST

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. [. . . ] To return to the normal playback mode, press (6) (BL SKIP) again. 9 Radio Memorizing stations automatically -- Best Tuning Memory (BTM) The unit selects the stations with the strongest signals and memorizes them in the order of their frequencies. You can store up to 6 stations on each band (FM1, FM2, AM1, and AM2). Caution When tuning in stations while driving, use Best Tuning Memory to prevent accidents. Memorizing only the desired stations You can store up to 6 stations on each band in the order of your choice. 1 2 3 4 Press (SOURCE) repeatedly to select the tuner. Press (MODE) repeatedly to select the band (FM1, FM2, AM1, or AM2). Press either side of (SEEK/AMS) to tune in the station you want to store on the number button. Press and hold the desired number button ((1) to (6)) until "PRESET" appears. The number button indication appears in the display. 1 Press (SOURCE) repeatedly to select the tuner. Each time you press (SOURCE), the source changes as follows: B CD B TAPE B TUNER 2 Note If you try to store another station on the same number button, the previously stored station will be erased. Press (MODE) repeatedly to select the band. Each time you press (MODE), the band changes as follows: B FM1 B FM2 B AM1 B AM2 Receiving the memorized stations 1 2 3 Press (SOURCE) repeatedly to select the tuner. Press (MODE) repeatedly to select the band (FM1, FM2, AM1, or AM2). Press the number button ((1) to (6)) momentarily where the desired station is stored. 3 Press (SENS/BTM) for two seconds. During playback, press (SA) for two seconds. Each time you press and hold (SA) for two seconds, the displayed item changes as follows: B L­1 B L­2* B L­3 Adjusting the bass curve Press (D-BASS) repeatedly to select the desired bass curve. Each time you press (D-BASS), the bass curve changes as follows: B D-BASS 1 B D-BASS 2 B D-BASS 3 No display (Cancel) b * Factory pre-setting As the D-BASS number increases so does the effect. To cancel the effect, press (D-BASS) repeatedly until "D-BASS" disappears. Note The bass sound may distort at same volume. If the bass sound distorts, select less effective bass curve. Turning off the beep tone Press (6) while pressing (SOUND). To obtain the beep tone again, press these buttons once more. 14 With Optional Equipment CD/MD unit You can control two CD or MD units with this unit. Locating a specific point in a track -- Manual Search During playback, press and hold either side of (SEEK/AMS). Release the button when you have found the desired point. SEEK/AMS Playing a CD or MD 1 2 Press (SOURCE) repeatedly until "CD" or "MD" appears. Press (MODE) repeatedly to select the desired CD/MD changer. CD/MD playback starts. To search backward To search forward Playing tracks repeatedly -- Repeat Play You can select: · REP 1 to repeat a track. · REP 3 to repeat all the discs in the current unit. During playback, press (2) (REPEAT) repeatedly until the desired setting appears. B REP 1 B REP 2* B REP 3* No display (Cancel) b When a CD/MD unit is connected, all the tracks play from the beginning. Switching to other discs During playback, press PRESET/DISC or . PRESET/ DISC To advance to the next disc To return to the previous disc Repeat Play starts. * "REP 2" and "REP 3" are only available when you connect one or more optional CD units, or when you connect two or more optional MD units. Changing the display item Each time you press (DSPL) during CD or MD playback, the item changes as follows: Disc number/ Track number/Elapsed playing time Y Clock To return to the normal playback mode, press (2) (REPEAT) repeatedly until "REP" desappears. Note When you play back a CD on this unit, Repeat 3 has the same function as Repeat 2. Locating a specific track -- Automatic Music Sensor (AMS) During playback, press either side of (SEEK/AMS) once for each track you want to skip. SEEK/AMS To locate preceding tracks To locate succeeding tracks 15 Playing tracks in random order -- Shuffle Play You can select: ·SHUF 1 to play the tracks on the current disc in random order. [. . . ] ·An optional power amplifier is connected and you are not using the built-in amplifier. ·The beep tone is muted. The contents of the memory have been erased. No beep tone. CD/MD playback Problem A disc cannot be loaded. Cause/Solution ·Another CD is already loaded. [. . . ]