User manual SONY XBR-52HX909

[. . . ] 4-180-193-11(1) LCD Digital Color TV Setup Guide (Operating Instructions) Setting up your TV To watch TV Additional Information Sony Customer Support U. S. A. : www. sony. com/tvsupport Canada: www. sony. ca/support United States 1. 800. 222. SONY Canada 1. 877. 899. SONY Please Do Not Return the Product to the Store KDL-55HX800 / 46HX800 / 40HX800 XBR-52HX909 / 46HX909 Owner's Record The information label are located on the rear of the TV. Record model name and serial numbers on the information label in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this TV. Licensing Information Macintosh is a trademark of Apple Inc. , registered in the U. S. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. [. . . ] ­ furniture that can easily be used as steps, such as a chest of drawers. · Install the TV where it cannot be pulled, pushed, or knocked over. · Route all AC power cords and connecting cables so that they are not accessible to curious children. Make sure the Stand can adequately support the weight of the TV. Use two angle braces (not supplied) to secure the stand. For each angle brace use the appropriate hardware to: · Attach one side of the angle brace to the wall stud. · Attach the other side to the Stand. Angle brace (not supplied) Stand 2 Secure the TV to the Stand Use the optional hardware listed below (not supplied): · M4 × 16 machine screw (screwed into the TV's Table-Top Stand) · A screw or similar (attach it to the Stand) · Rope or chain (strong enough to support the weight of the TV). Make sure that there is no excess slack in the rope or chain. An alternative way to secure the TV is with an optional Sony Support Belt Kit. M4 × 16 machine screw (not supplied) Screw hole on the Table-Top Stand Rope or chain (not supplied) Screw (not supplied) ~ Contact Sony Customer Support to obtain the optional Support Belt Kit by providing your TV model name. · For United States call: 1-800-488-7669 or visit: www. sony. com/accessories · For Canada call: 1-877-899-7669 12 3 Anchor the TV to the Wall Anchor the TV to the wall by using bolts, wall anchor and chain (or rope). Anchor bolts (not supplied) Organizing the AC power cord Wallmount holes Rope or chain (not supplied) Setting up your TV Wall-anchor (not supplied) ~ · KDL-55HX800 is shipped with screws attached to the rear of the TV. (They are fastened in the screw holes for wall mounting. ) Be sure to remove the upper two screws prior to installing the TV on a wall. · Securing the TV to the stand without securing the TV and the stand to the wall provides minimum protection against the TV toppling over. For further protection, be sure to follow the three measures recommended. 13 Running initial setup POWER Detaching the Table-Top Stand from the TV Remove only the screws marked with the TV. on 1 Complete your cable connections before proceeding with the Initial Setup. Connect the TV to your nearest power outlet. Check the ENERGY SAVING SWITCH setting is on (z). When you switch the TV on for the first time, the Language menu appears on the screen. 2 3 ~ · Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the TV. · For XBR-52/46HX909 and KDL-40HX800, remove the stand rear cover prior to detaching the Table-Top Stand. · For KDL-55HX800, when installing the TV on a wall, remove the four screws from the rear of the TV. (They are fastened in the screw holes for wall mounting. ) Be sure to store the removed screws in a safe place, keeping them away from children. · For KDL-55HX800, when attaching the TableTop Stand again, be sure to fasten the four screws (previously removed) to the original holes on the rear of the TV. · Do not hold by the stand rear cover while carrying the Table-Top Stand to prevent dropping the stand which may cause an injury or damage to the property. 4 Follow the instructions on the screen. ~ · The ENERGY SAVING SWITCH must be on (z) to set the clock and obtain program information for the TV Guide. · Home mode sets the TV to settings optimized for home viewing (this setting is ENERGY STAR compliant). 5 Select Continue to scan for available channels and enable the TV Guide On Screen® feature. [. . . ] 3D Sync terminal for optional transmitter RS232C, D-sub 9 pin. This jack is for receiving the external control signal. Channel coverage Panel system Speaker output Input/Output jacks CABLE/ANTENNA VIDEO IN 1/2 COMPONENT IN 1/2 HDMI IN 1/2/3/4 AUDIO OUT DIGITAL AUDIO OUT (OPTICAL) PC IN PC/HDMI 4 AUDIO INPUT LAN USB/DLNA 3D SYNC REMOTE (HX909 series only) Model name KDL-/XBRPower and others Power requirement Power consumption in use in DAM*2 in standby Screen size (inches measured diagonally) Display resolution Speaker Full range with speaker (mm) box (2) (inches) Dimensions with stand (mm) (inches) 55HX800 52HX909 46HX909 46HX800 40HX800 110 V - 240 V AC, 50/60 Hz (U. S. A. /Canada 120 V AC, 60 Hz) 167 W 201 W 184 W 149 W 132 W 14 W (You may hear a clicking noise during the download but this is normal. ) Less than 0. 12 W with 120 V AC and less than 0. 2 W with 240 V AC 54. 6 inches 52 inches 46 inches 40 inches (55 class) 1, 920 dots (horizontal) × 1, 080 lines (vertical) 34 × 160 1 3/8 × 6 3/8 34 × 100 1 3/8 × 4 1, 263 × 807 × 400 49 3/4 × 31 7/8 × 15 3/4 1, 263 × 775 × 67 49 3/4 × 30 5/8 × 2 3/4 34 × 160 1 3/8 × 6 3/8 952 × 613 × 250 37 1/2 × 24 1/4 × 9 7/8 952 × 581 × 74 37 1/2 × 22 7/8 × 3 1, 278 × 797 × 350 50 3/8 × 31 1/2 × 13 7/8 without stand (mm) 1, 278 × 765 × 73 (inches) 50 3/8 × 30 1/8 × 2 7/8 wall-mount hole pattern (mm) 400 × 300 wall-mount screw size (mm) 1, 124 × 727 × 400 1, 085 × 688 × 260 44 3/8 × 28 5/8 × 42 3/4 × 27 1/8 × 15 3/4 10 1/4 1, 124 × 695 × 67 1, 085 × 656 × 74 44 3/8 × 27 3/8 × 42 3/4 × 25 7/8 × 3 2 3/4 300 × 300 M6 (length: refer to diagram on page 15. ) with stand (kg)/(lb. ) 26. 9/59. 3 42. 9/94. 5 36. 2/79. 8 19. 2/42. 3 16. 4/36. 2 without stand (kg)/(lb. ) 22. 6/49. 8 36. 9/81. 3 30. 2/66. 6 16. 9/37. 3 14. 2/31. 3 See "Checking the accessories" (page 4). Supplied accessories Optional accessories Connecting cables / Support Belt Kit / Wall-Mount Bracket / TV Stand / 3D Glasses (TDG-BR100/TDGBR50) / 3D Sync Transmitter (TMR-BR100) Mass *1 For LAN connections, use a Category 7 10BASE-T/100BASE-TX cable (not supplied). *2 Download Acquisition Mode (DAM) is used for software updates and/or collecting data for TV Guide On Screen. [. . . ]