User manual SONY XC-ES51CE

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] B 1 2 3 4 3 GND1 1 The CCD Black-and-White Video Camera Module XC-ES/EI series system comprises the following optional products (available separately). CCD 2 CCXC-12P02N 2m /05N 5m /10N 10m / 25N 25m) DC IN/SYNC 1 CCD Black-and-White Video Camera Module This is a small-size, high-resolution, monochrome video camera module using an interline transfer CCD image sensor. 2 CCXC-12P02N (2 m, 6. 6 ft)/05N (5 m, 16. 4 ft)/10N (10 m, 32. 8 ft)/25N (25 m, 82 ft) camera cable This is attached to the DC IN/SYNC connector of the camera module and is used for power supply, transmission of video signals, and exchange of sync signals. 3 C-mount lens (For visible light) Recommended lens: VCL-08YM/12YM/16Y-M/25Y-M/50Y-M 4 DC-700/700CE camera adaptor This is connected to the camera module to enable power supply from ordinary AC power source, and also handles transmission of video signals from the camera module and exchange of sync signals between the camera module and an external sync signal generator. 3C DC GND3 VCL-08YM/12YM/16Y-M/25Y-M/50Y-M 4 DC-700 AC B 1 2 5 VCT-333I C 3 DC-700 DC-700 DC-700 1 2C 3 75 4 5 TRIG 6 1 2 3 4 5 6 7 8 9 5 VCT-333I tripod adaptor This attaches to the bottom of the camera module to fix the camera module to a tripod. DC-700 DC IN/SYNC VIDEO 1 CAMERA AC IN AC HD VD/SYNC HD VD Connection example Connecting DC-700/700CE (not supplied) Fig. C · · · · · 4 5 VCL-16Y-M CCXC-12P05N Connect the camera module to the power via the DC-700/700CE camera adaptor. For details on the DC-700/700CE camera adaptor, refer to the DC-700/ 700CE Instruction Manual. VCL-16Y-M) 75 coaxial cable Camera cable (e. g. CCXC-12P05N) TRIG generator, Image processor Sync. signal generator 1 2 3 4 5 6 7 8 9 DC IN/SYNC connector To VIDEO 1 connector To CAMERA connector To AC IN connector To AC power source To HD connector To VD/SYNC connector HD output VD output C 1 1 3 DC-700/700CE 2 WEN HD VIDEO 1 XC-ES/EI XC-ES/EI series D 2 1 4 C ) 3 CAMERA AC IN C Location and Function of Parts and Operation Front/Top/Bottom 4 5 Fig. D C 1 2 7mm 7mm 1 1 TRIG 1 2 2 1 Lens mount (C-mount) Attach any C-mount lens or other optical equipment. Note The lens must not project more than 7 mm (9/32 inch) from the lens mount. 1 Lens mount face 2 7 mm (9/32 inch) or less 2 Reference holes (Top) 3 Reference holes/Tripod screw holes (bottom) 4 Reference holes (bottom) These precision screw holes are for locking the camera module. Locking the camera module into these holes secures the optical axis alignment. VD/SYNC 5 8 6 9 6 7 2 3 4 34 4 VCT-333I For details on dimensions, etc. , see "About the Technical Manual" on the lower right of the back side. D 1 2 You can install the camera on a tripod. To install on a tripod, you will need to install the VCT-333I tripod adaptor to the camera on the reference holes 3. 3 4 2 1 Note Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER. E 5 6 1 2 3 4 5 6 1 2 3 4 5 6 7 VD ( -- -- -- -- ) DC 12V ( ( HD ( HD ( 8 ) ) ) ) 9 10 11 12 VD ( F ) DIP 1 F-a bit 1 4 DC 12V ( 9 16V) XC-ES51/ES50/EI50: 1. 6W XC-ES30/EI30: 1. 4W 10 45 20 60 20 80 ( ) 20 95 ( ) 10G (20Hz 200Hz) 70G 29 (W) 29 (H) 32 (D)mm 50g (1) (1) Phenomena specific to CCD image sensors The following phenomena that may appear in images are specific to CCD (Charge Coupled Device) image sensors. They do not indicate malfunctions. White flecks Although the CCD image sensors are produced with high-precision technologies, fine white flecks may be generated on the screen in rare cases, caused by cosmic rays, etc. This is related to the principle of CCD image sensors and is not a malfunction. [. . . ] · If you set the External trigger shutter mode, set 0 in bits 1­4. 7 HD/VD signal input/output switch Set the switch to INT to output the HD/VD signals from the camera module. Set the switch to EXT to input the HD/VD signals from an external unit. [. . . ]