User manual SONY XDR-DS12IP

[. . . ] WARNING 4-199-738-12(1) To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of fire, do not cover the ventilation of the apparatus with newspapers, tablecloths, curtains, etc. And do not place lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. [. . . ] The reset button is in the small hole located in the battery compartment (see Fig. ). To activate Auto DST/summer time adjustment again Press MENU and SELECT or to select the "Auto DST, " and then press ENTER. Press SELECT or to select "ON, and then press ENTER again. " The " " mark appears in the display. The time returns to summer time. iPod classic iPhone About the backup battery To keep accurate time, this unit contains a CR2032 battery as a backup power source. The battery keeps the clock and the alarm operating in the event of a power interruption. Operating the radio The unit can receive DAB service and FM stations. Auto preset tuning (FM only) 1 Press DAB/FM repeatedly to select the 2 Press MENU and SELECT or to select 3 Press SELECT or to select "Yes, " and then press ENTER. The unit automatically presets the available channels for both FM1 and FM2 in order. Tip To stop auto preset tuning, press OFF. Setting the clock manually Do the following if DAB broadcast is not available (depending on area). The time setting mode by DAB becomes invalid. 1 Press DAB/FM repeatedly to select the desired band. Each press changes the band as follows: DAB1 FM2 DAB2 FM1 FM band. Setting the clock for the first time When the first time after purchase, do the following. "Auto Preset, " and then press ENTER. To know when to replace the battery When the battery becomes weak, "" appears in the display. If a power interruption occurs while the battery is weak, the current time and alarm settings will be lost. Replace the battery with a Sony CR2032 lithium battery. Use of another battery may cause a fire or explosion. 1 Plug in the unit. 2 Press MENU and SELECT or to select "Date & Time, " and then press ENTER. The year flashes in the display. 3 Press SELECT or to set the year, and 4 Repeat step 3 to set the month, day, hour and minute. The seconds start incrementing from zero. then press ENTER. FM1 and FM2 or DAB1 and DAB2 are the same frequency bands. If a list of receivable DAB broadcasts has not been created when you select DAB1 or DAB2, "Scanning. . . " will appear in the display, and the unit starts scanning automatically. Continued on the reverse side The connector of the unit is exclusively for use with an iPod. If you use a device that does not match the connector, connect it to the AUDIO IN jack of this unit with the supplied audio connecting cable. Sony cannot accept responsibility in the event that data recorded on an iPod is lost or damaged when using an iPod connected to this unit. For details of environmental conditions for operating your iPod, check the website of Apple Inc. To set the alarm 1 Press and hold ALARM SET A or B. 2 Press ALARM TIME SET + or ­ "Alarm­A Setting" or "Alarm­B Setting" appears and the hour flashes in the display. 7 If "A" or "B" does not appear in the The radio will turn on at the set time. display, press ALARM SET A or B again. During a power interruption, each alarm will sound at the set time only once. repeatedly until the desired hour appears. To cycle the hour rapidly, press and hold ALARM TIME SET + or ­. The minute flashes. 3 Press ALARM SET A or B. 1 Attach the adapter for your iPod/iPhone, 2 and then insert your iPod/iPhone into the connector of the unit (see Fig. Press iPod & iPhone . The iPod begins to play automatically. You can operate the connected iPod by this unit or the iPod buttons. Note If the selected preset number is not set, or there is no last station, the alarm sound will be buzzer when alarm time is met. If you want to change the buzzer alarm, set preset station or tune radio station (see "Operating the radio"). Setting the sleep timer You can fall asleep to music, etc. , using the sleep timer. The unit stops playback or radio automatically after a preset duration. Notes If there is no component label, "NO COMP LABEL" will be displayed. [. . . ] ­ : scans downwards through the frequency bands. Scanning starts from the currently-tuned frequency. When a station is received, scanning stops. You can enjoy iPod audio by connecting to this unit. To use an iPod, refer to the user's guide of your iPod. [. . . ]