User manual SONY XM-DS1300P5

[. . . ] 3-265-661-11 (1) Features ·Maximum power output of 800 W (at 2 ). ·Class D Technology* ·This Power Amplifier is designed to be used with subwoofers only. ·Direct connection can be made with the speaker output of your car audio unit if it is not equipped with a line output (High level input connection). ·Built in variable LPF (Low-pass filter), subsonicfilter (OFF/ON, 15 Hz), and low boost circuit. [. . . ] t Remédiez à la cause du court-circuit. Coupez l'interrupteur d'alimentation. Assurez-vous que le cordon de hautparleur et le câble de masse sont correctement branchés. · L'appareil chauffe de façon anormale. L'alternateur émet un bruit. · Utilisez des haut-parleurs d'une impédance appropriée. · Installez l'appareil dans un endroit bien aéré. Le protecteur thermique est activé. Les câbles d'alimentation sont installés trop près des câbles à broches RCA. t Éloignez les câbles d'alimentation des broches RCA. Le câble de masse n'est pas connecté correctement. t Fixez correctement le câble de masse à un point métallique de la voiture. Les câbles négatifs des haut-parleurs touchent la carrosserie de la voiture. t Éloignez les câbles de la carrosserie de la voiture. ø 5 × 15 (× 5) 0. 2 m 0 5 10 40 100 300 Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 200 watts minimum continuous average power into 4 ohms, 20 Hz to 300 Hz with no more than 0. 2% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications Class D Technology Pulse power supply RCA pin jacks High level input connector Outputs Speaker terminals Through out pin jacks Suitable speaker impedance 2­8 Maximum outputs 400 W (at 4 ) 800 W (at 2 ) Rated outputs (supply voltage at 14. 4 V) 200 W (20 Hz ­ 300 Hz, 0. 2 % THD, at 4 ) 400 W (20 Hz ­ 300 Hz, 0. 6 % THD, at 2 ) Frequency response 5 ­ 300 Hz ( dB) Harmonic distortion 0. 06 % or less (at 100 Hz, 4 ) Input level adjustment range 0. 3 ­ 6. 0 V (RCA pin jacks) 1. 2 ­ 12. 0 V (High level input) Inputs Circuit system Sub-sonic filter 15 Hz, ­ 12 dB/oct Low-pass filter 50 ­ 300 Hz, ­ 12 dB/oct Low boost 0 ­ 10 dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10. 5 ­ 16 V Current drain at rated output: 50 A (at 2 ) Remote input: 2 mA Dimensions Approx. 295 × 57 × 290 mm (11 5/8 × 2 1/4 × 11 1/2 in. ) (w/h/d) not incl. projecting parts and controls Mass Approx. accessories Supplied accessories Mounting screws (5) High level input cord (1) Protection cap (1) Design and specifications are subject to change without notice. Frequency/Fréquence Hz Subsonic Filter/Filtre subsonique dB 12. 0 0 OFF ON (15 Hz) Unit : mm (in. ) Unité : mm (po) 57 (2 1/4) 278 (11) 6 (1/4) Le son est trop faible. La commande de réglage LEVEL n'est pas appropriée. Tournez la commande de réglage LEVEL dans le sens des aiguilles d'une montre. 1 -30. 0 Frequency/Fréquence Hz Low Pass Filter/Filtre passe-bas dB 10 0 -10 290 (11 1/2) 264 (10 1/2) 5 10 100 101 (4) 172 (6 7/8) 295 (11 5/8) LOW PASS 300Hz -20 -30 -40 -50 100Hz 50Hz -60 10 100 1k 2k · Halogenated flame retardants are not used in cabinets. · Corrugated cardboard is used for the packaging cushions. Frequency/Fréquence Hz Connections Caution · Before making any connections, disconnect the ground terminal of the car battery to avoid short circuits. · Be sure to use speakers with an adequate power rating. If you use small capacity speakers, they may be damaged. · Do not connect the # terminal of the speaker system to the car chassis. [. . . ] A loose connection may cause a malfunction of the amplifier. · Be sure to connect the remote control wire of the car audio to the remote terminal. · When using a car audio without a remote output on the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. · Use the power supply wire with a fuse attached (80 A). [. . . ]