User manual SONY XPR120

[. . . ] Highlighted letters in the text of this manual correspond to the illustrations. PRECAUTIONS To maintain good performance XP-R120 COMPACT DISC PLAYER OPERATING INSTRUCTIONS · Do not use the unit in places which are extremely hot, cold, dusty or humid. In particular, do not use or keep the unit in following places. · in a high humidity area such as a bathroom · near a heater · in an area exposed to direct sunlight (e. g. , inside a parked car, where it can become extremely hot) · near sources of strong magnetism, such as televisions, speakers, or magnets · where there is a lot of movement or vibration, such as on a car dashboard or an unstable shelf For safety · Do not attempt to disassemble the unit. Laser rays from the optical pickup are dangerous to the eyes. [. . . ] Connect the AC adaptor in the same way as when recharging the batteries. During operation on AC house current, all of the battery indicator disappears. BEFORE PLAYBACK HOLD switch F Release the HOLD switch before playback. a When not using the unit, set the HOLD switch to the HOLD position. b Accidentally pressed button will not function. If buttons are pressed when the HOLD switch is set to the HOLD position, "HOLd" flashes in the display. Turning on and off F H1 Turning the power on Press ePLAY/PAUSE. Power is turned on and playback starts. Note "Err" appears on the display when you play a disc placed upside-down or a defective disc. Turning the power off If no new operations are done within 30 seconds from the end of last operation, the power is turned off automatically. (Auto power off function) · You can turn off the power by pressing sSTOP/OFF/CHARGE before it is automatically turned off. 2 3 Standby mode F When an operation finishes, the unit goes into standby mode until the auto power off function automatically turns off the power. · When trying to program tracks beyond No. 32. · When the total remaining time of the programmed tracks is over 100 minutes. E·A·S·S 2×(Electronic Anti-Shock System) L K ENTER/DISP The E·A·S·S 2× function reduces skipping or muting of the sound when the unit is subjected to shocks. To activate the E·A·S·S 2× function, set the E·A·S·S switch to ON. To cancel the E·A·S·S 2× function, set the E·A·S·S switch to OFF. display changes to Note · Before jogging with this unit, allow sufficient time for the memory buffer to fill up completely (ideally about 20 seconds). Continuous shock or vibration may cause the sound to be interrupted even if the E·A·S·S 2× function is activated. Should you experience an interruption in sound, stabilize the unit for a few seconds, then resume your activity. · When the E·A·S·S 2× function is activated, motor noise is heard as the motor periodically rotates at high speed during playback. · When the E·A·S·S switch is slid during playback, the unit will pause for about 2 seconds. · When you set the E·A·S·S switch to the OFF position, the quality of the sound will be better than the case that you set it to the ON position. Resume function M L Set the HOLD switch to RESUME. appears, and you can start playback from the point where you stopped playback by pressing sSTOP/OFF/CHARGE. When the resume function is on, all-track repeat is selected automatically. To cancel resume play, set the HOLD switch to OFF. Note · Resume play may start at a point about 30 seconds behind or ahead the stopped point. Resume play may not operate if you stopped at the last 30 seconds of the final track. · Resume play will be canceled if you open the disc compartment. [. . . ] 3 Press ENTER/DISP to preset the station. a Preset number To preset more stations, repeat steps 2 and 3. Listening to preset stations S R 1 Press BAND TUNER ON repeatedly to select AM or FM. 2 Press PRESET CALL UP/DOWN repeatedly to select the preset number. After listening, press sSTOP/OFF/CHARGE to turn off the radio. Changing the presetting 1 Press PRESET CALL UP/DOWN repeatedly to select the preset number you wish to change. [. . . ]