User manual SONY XPR210

[. . . ] d c OWNER'S RECORD For your convenience, record the model number and the serial number (you will find it on the bottom of your set) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty. Model No. XP-R210 COMPACT DISC PLAYER Serial No. NOTE FOR USE IN THE U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] If buttons are pressed when the HOLD switch is set to the HOLD position, "HOLd" flashes in the display. HOLD switch D Turning on and off D Turning the power on Press e PLAY/PAUSE. Power is turned on and playback starts. Note "Err" appears on the display when you play a disc placed upside-down or a defective disc. F1 Turning the power off If no new operations are done within 30 seconds from the end of last operation, the power is turned off automatically. (Auto power off function) · You can turn off the power by pressing sSTOP/OFF/CHARGE before it is automatically turned off. Standby mode D When an operation finishes, the unit goes into standby mode until the auto power off function automatically turns off the power. To enter standby mode, press e PLAY/PAUSE to start playback, then press sSTOP/OFF/CHARGE. 2 3 Adjusting the sound E Volume Turn the VOL control to adjust the volume. DSL Press DSL repeatedly for more powerful sound and deeper bass. : Normal sound Signal sound function G You can check the operation by beep sound when you press an operation button. The signal sound function is not activated when you purchase this unit. To use the signal sound function, press ePLAY/PAUSE while pressing PLAY MODE while in stop mode. The beep sound is heard when you press a button. To cancel the beep sound, repeat this procedure. Inserting a disc F 1 Slide the OPEN switch to open the disc compartment. 2 Place a disc in the center with the label side facing up. 3 Close the disc compartment. To remove the disc G Pick up the disc, holding its edge, while pressing the pivot gently. Note · The unit may not play a CD-R/RW disc that is recorded on personal computers or some kinds of CD-R/RW recorders because of differences in recording platforms. · Do not attach any seal or label to either side (the recordable side or the labeled side) of a CD-R/RW disc. It may cause malfunction. H PLAYBACK H Connect the supplied headphones to the PHONES/LINE OUT jack. a track number b elapsed playing time Basic operation To stop To pause Press sSTOP/OFF/CHARGE. Release the button at the start of desired passage. 1 2 To search for the beginning of a track To locate a desired passage Display during playback I Press ENTER/DISP during playback to change the display as follows. 1 Track display and elapsed playing time (normal display) V 2 Track display and remaining playing time of the track in play 3 V 3 Remaining number of tracks and remaining playing time The time is not displayed in following cases. · When trying to program tracks beyond No. 32. · You cannot select one-track repeat during random play. Repeat play K Press PLAY MODE during playback to select repeat play as follows. K : one-track repeat B V : all-track repeat V no repeat play (normal play) V com letely (ideally 40 to 48 seconds). Continuous shock or vibration may cause the sound to be interrupted even if the E·A·S·S PLUS function is activated. Should you experience an interruption in sound, stabilize the unit for a few seconds, then resume your activity. · When the E·A·S·S switch is slid during playback, the unit will pause for about 2 seconds. · When you set the E·A·S·S switch to the 12 or OFF position, the quality of the sound will be better than the case that you set it to the 48 position. V Resume function K Set the HOLD switch to RESUME. [. . . ] · DO NOT connect to the PHONO inputs of an amplifier (with a built-in phonoequalizer-amplifier). · Adjust the volume and DSL on this unit. Q MAINTENANCE To clean the lens S If the lens becomes dirty, the player will skip or not play. If this occurs, clean the lens in the following manner. To remove dust or dry particles, first use a camera lens blower/brush a to blow a few times to loosen particles, then gently brush the lens b clean. [. . . ]