User manual SONY XPR220

[. . . ] Highlighted letters in the text of this manual correspond to the illustrations. PRECAUTIONS To maintain good performance XP-R220 COMPACT DISC PLAYER OPERATING INSTRUCTIONS · Do not use the unit in places which are extremely hot, cold, dusty or humid. In particular, do not use or keep the unit in following places. · in a high humidity area such as a bathroom · near a heater · in an area exposed to direct sunlight (e. g. , inside a parked car, where it can become extremely hot) · near sources of strong magnetism, such as televisions, speakers, or magnets · where there is a lot of movement or vibration, such as on a car dashboard or an unstable shelf For safety · Do not attempt to disassemble the unit. Laser rays from the optical pickup are dangerous to the eyes. [. . . ] If buttons are pressed when the HOLD switch is set to the HOLD position, "HOLd" flashes in the display. Turning on and off F Turning the power on H1 Press ePLAY/PAUSE. Power is turned on and playback starts. Note "Err" appears on the display when you play a disc placed upside-down or a defective disc. Turning the power off If no new operations are done within 30 seconds from the end of last operation, the power is turned off automatically. (Auto power off function) · You can turn off the power by pressing sSTOP/OFF/CHARGE before it is automatically turned off. Standby mode F 2 3 When an operation finishes, the unit goes into standby mode until the auto power off function automatically turns off the power. To enter standby mode, press ePLAY/PAUSE to start playback, then press sSTOP/OFF/CHARGE. Adjusting the sound G Volume Turn the VOL control to adjust the volume. DSL Press DSL repeatedly for more powerful sound and deeper bass. : Normal sound I Signal sound function To enter standby mode, press ePLAY/PAUSE to start playback, then press sSTOP/OFF/CHARGE. Adjusting the sound G Volume Turn the VOL control to adjust the volume. DSL Press DSL repeatedly for more powerful sound and deeper bass. : Normal sound I Signal sound function You can check the operation by beep sound when you press an operation button. The signal sound function is activated when you purchase this unit. To use the signal sound function, press ePLAY/PAUSE while pressing " while in stop mode. The beep sound is heard PLAY MODE to display " when you press a button. To cancel the beep sound, repeat this procedure. Inserting a disc H 1 Slide the OPEN switch to open the disc compartment. 2 Place a disc in the center with the label side facing up. 3 Close the disc compartment. To remove the disc I Pick up the disc, holding its edge, while pressing the pivot gently. Note · The unit may not play a CD-R/RW disc that is recorded on personal computers or some kinds of CD-R/RW recorders because of differences in recording platforms. · Do not attach any seal or label to either side (the recordable side or the labeled side) of a CD-R/RW disc. It may cause malfunction. XP-R220 (AU) E Page 1 J PLAYBACK J Connect the supplied headphones to the PHONES/LINE OUT jack. The amplified speaker system can be connected instead to enjoy the CD sound. a track number b elapsed playing time Basic operation To stop To pause Press sSTOP/OFF/CHARGE. Release the button at the start of desired passage. 1 2 To search for the beginning of a track To locate a desired passage Display during playback K Press ENTER/DISP during playback to change the display as follows. 1 Track display and elapsed playing time (normal display) V 2 Track display and remaining playing time of the track in play 3 V 3 Remaining number of tracks and remaining playing time The time is not displayed in following cases. · When trying to program tracks beyond No. 32. · When the total remaining time of the programmed tracks is over 100 minutes. E·A·S·S 3× (Electronic Anti-Shock System) L K ENTER/DISP The E·A·S·S 3× function reduces skipping or muting of the sound when the unit is subjected to shocks. The player keeps about 48 seconds or 12 seconds of playback sound in its memory. To keep 48 seconds in the memory, set the E·A·S·S switch to 48. [. . . ] 4 Keep ENTER/DISP pressed for more than 5 seconds. The unit searches for and memorizes the receivable stations. Automatic presetting ends after 30 stations are preset. To stop presetting before 30 stations are preset, press sSTOP/OFF/ CHARGE. [. . . ]