User manual SONY XPSR311

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on circuit different from that to which the receiver is connected. [. . . ] After charging, disconnect the AC adaptor. Time to recharge the batteries D CHARGE Recharge the batteries when lights. If the unit remains in use after lights, "Lo-bAtt" is displayed and the current operation will stop. To stop charging Press sSTOP/OFF/CHARGE during charging. ATTENTION: The product you have purchased can be powered by nickel cadmium batteries which are recyclable. At the end of their useful life, under various state and local laws, it is illegal to dispose of these batteries into your municipal waste stream. Please call 1-800-289-2492 for information on how to recycle these batteries. HOLD RESUME OFF PLAY/ PAUSE STOP/OFF E DSL E VOLUM USING ON AC HOUSE CURRENT Connect the supplied AC adaptor in the same way as when recharging the batteries. During operation on AC house current, all of the battery indicators disappear. BEFORE PLAYBACK HOLD switch D Release the HOLD switch before playback. a When not using the unit, set the HOLD switch to the HOLD position. Accidentally pressed button will not function. b If buttons are pressed when the HOLD switch is set to the HOLD position, "HOLd" flashes in the display. F Turning on and off D Turning the power on Press e PLAY/PAUSE. Power is turned on and playback starts. Note "Err" appears on the display in the following cases: ­ When you try to play the unit without a disc in the disc compartment. ­ When you play a disc placed upside-down or a defective disc. Turning the power off PHONES/ LINE OUT If no new operations are done within 30 seconds from the end of last operation, the power is turned off automatically. (Auto power off function) · You can turn off the power before it is automatically turned off by pressing sSTOP/OFF/CHARGE. G1 2 Standby mode D When an operation finishes, the unit goes into standby mode until the auto power off function automatically turns off the power. To enter standby mode, press e PLAY/PAUSE to start playback, then press sSTOP/OFF/CHARGE. Adjusting the sound E Volume Press + to increase the volume. Press - to decrease the volume. 3 H DSL Press DSL for more powerful sound and deeper bass. : Normal sound 3 H DSL Press DSL for more powerful sound and deeper bass. : Normal sound Connecting the headphones F Pull out the rubber cap and connect the supplied headphones to the PHONES/LINE OUT jack. Inserting a disc G 1 Set the dial to the OPEN position to open the disc compartment. 2 Place a disc in the center with the label side facing up. 3 Close the disc compartment tightly and set the dial to the LOCK position. To remove the disc H Pick up the disc, holding its edge, while pressing the pivot gently. Note · The unit may not play a CD-R/RW disc that is recorded on personal computers or some kinds of CD-R/RW recorders because of differences in recording platforms. · Do not attach any seal or label to either side (the recordable side or the labeled side) of a CD-R/RW disc. It may cause malfunction. XP-SR311(AU)E Page 1 I 3 1 2 STOP/OFF/ CHARGE PLAYBACK I Pull out the rubber cap and connect the supplied headphones to the PHONES/LINE OUT jack. 1 Release HOLD. [. . . ] To remove dust or dry particles, first use a camera lens blower/brush a to blow a few times to loosen particles, then gently brush the lens b clean. To remove fingerprints, use a cotton swab dipped in lens cleaning solution. Wipe gently from the center to the edge. Lens cleaning solution is commercially available. PHONES/ LINE OUT Note Take care not to get too much solution on the swab, which could flow into the unit and cause damage. [. . . ]