User manual SONY XR-C620RDS SERVICE MANUAL

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. [. . . ] The unit stores stations in the order of their frequencies on the number buttons. A beep sounds when the setting is stored. Press (SHIFT). 5 Notes · The unit does not store stations with weak signals. If only a few stations can be received, some number buttons will retain their former setting. · When a number is indicated in the display, the unit starts storing stations from the one currently displayed. 8 Memorizing only the desired stations You can preset up to 18 FM stations (6 each for FM1, 2, and 3) and up to 12 AM stations (6 each for AM1 and 2) in the order of your choice. If you cannot tune in a preset station Push and release the SEEK/AMS control up or down to search for the station (automatic tuning). Scanning stops when the unit receives a station. Push the SEEK/AMS control up or down repeatedly until the desired station is received. Note If the automatic tuning stops too frequently, press (SHIFT), then press (3) (PLAY MODE) repeatedly until "LOCAL" (local seek mode) is displayed. Then press (4) (n) to select "LOCAL-ON. " Press (SHIFT). Only the stations with relatively strong signals will be tuned in. Tip If you know the frequency of the station you want to listen to, push the SEEK/AMS control up or down and hold until the desired frequency appears (manual tuning). 1 2 3 4 Press (SOURCE) repeatedly to select the tuner. Press (MODE) repeatedly to select the band. CD/MD playback starts. 0dB Frequency (Hz) Adjusting the bass curve Turn the D-BASS control to adjust the bass level (1, 2, or 3). "D-BASS" appears in the display. To cancel, turn the control to OFF. Note If the bass sound becomes distorted, adjust the D-BASS control or volume. When a CD/MD unit is connected, all the tracks play from the beginning. Changing the display item Each time you press (DSPL) during CD, or MD playback, the item changes as follows: $ Elapsed playback time $ Disc name*1 $ Track name*2 $ Clock *1 If there is no disc name prerecorded on the MD, "NO NAME" appears in the display. *2 If the track name of an MD is not prerecorded, "NO NAME" appears in the display. After you select the desired item, the display will automatically change to the Motion Display mode after a few seconds. In the Motion Display mode, all the above items are scrolled in the display one by one in order. Tip The Motion Display mode can be turned off. (See "Changing the sound and display settings" on page 12). 13 Automatically scrolling a disc name -- Auto Scroll If the disc name or track name on an MD exceeds 8 characters and the Auto Scroll function is on, information automatically scrolls across the display as follows: · The disc name appears when the disc has changed (if the disc name is selected). · The track name appears when the track has changed (if the track name is selected). Locating a specific track -- Automatic Music Sensor (AMS) During playback, push the SEEK/AMS control up or down and release for each track you want to skip. SEEK / AMS To locate succeeding tracks To locate preceding tracks If you press (DSPL) to change the display item, the disc or track name of the MD is scrolled automatically whether you set the function on or off. Locating a specific point in a track -- Manual Search During playback, push the SEEK/AMS control up or down and hold. Release when you have found the desired point. SEEK / AMS 1 2 3 4 During playback, press (SHIFT). Press (2) (SET UP) repeatedly until "A. SCRL" appears. Press (4) (n) to select "A. SCRL-ON. " To search forward To search backward Press (SHIFT). To cancel Auto Scroll, select "A. SCRL-OFF" in step 3 above. Note For some MDs with very many characters, the following cases may happen: -- Some of the characters are not displayed -- Auto Scroll does not work. Tip To manually scroll the long name of an MD after activating the Auto Scroll function, press (SHIFT), then (1) (N) (manual scroll). Changing Discs During playback, press either side of (PRESET/DISC) momentarily. [. . . ] Cause/Solution ·Cancel the ATT function. ·Set the fader control to the center position for two-speaker systems. ·Rotate the dial clockwise to adjust the volume. · The power cord or battery has been disconnected. [. . . ]