User manual SONY XR-DV700

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. [. . . ] 1 Volume +/­ button 7 2 MODE button During radio reception: BAND select 8, 9 During CD/MD playback: CD/MD unit select 12 3 SOURCE (TUNER/CD/MD) button 8, 9, 12 4 SEL (select) button 7, 10, 11, 12 5 Z (eject) button 7, 8, 9, 12 6 Display window 7 m/M (fast winding)/DIR (tape transport direction change) buttons 7, 8 8 MBP (My Best sound Position) button 11 9 D-BASS button 11 q; SEEK/AMS +/­ button 9, 13 Seek 9 Automatic Music Sensor 13 Manual search 13 qa RELEASE (front panel release) button 6, 14 qs ATT (attenuate) button 10 qd SENS button 9 qf RESET button (located on the front side of the unit behind the front panel) 6 qg Frequency select switch* (located on the bottom of the unit) See "Frequency select switch" in the Installation/Connections manual. qh Number buttons 8, 9, 10, 12, 13 During radio reception: Preset number select 9 During tape playback: (6) ATA 8 During CD/MD playback: (1) DISC ­ 13 (2) DISC + 13 (3) REP 13 (4) SHUF 13 qj BTM button 8 qk DSPL (display mode change) button 7, 12 ql OFF button** 6 * XR-CA305 only ** Warning when installing in a car without ACC (accessory) position on the ignition key switch Be sure to press (OFF) on the unit for two seconds to turn off the clock display after turning off the engine. When you press (OFF) momentarily, the clock display does not turn off and this causes battery wear. 5 Attaching the front panel Getting Started Resetting the unit Before operating the unit for the first time or after replacing the car battery, you must reset the unit. Remove the front panel and press the RESET button with a pointed object, such as a ballpoint pen. Attach part A of the front panel to part B of the unit as illustrated and push the left side into position until it clicks. A B RESET button Note Pressing the RESET button will erase the clock setting and some memorized functions. Detaching the front panel You can detach the front panel of this unit to protect the unit from being stolen. Notes · Be sure not to attach the front panel upside down. · Do not press the front panel too hard against the unit when attaching it. · Do not press too hard or put excessive pressure on the display window of the front panel. · Do not expose the front panel to direct sunlight or heat sources such as hot air ducts, and do not leave it in a humid place. Never leave it on the dashboard of a car parked in direct sunlight or where there may be a considerable rise in temperature. Caution alarm If you turn the car ignition off without removing the front panel, the caution alarm will beep for a few seconds. If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. 1 2 Press (OFF). Press (RELEASE), then slide the front panel a little to the left, and pull it off towards you. (OFF) (RELEASE) Notes · Be sure not to drop the panel when detaching it from the unit. · If you detach the panel while the unit is still turned on, the power will turn off automatically to prevent the speakers from being damaged. In case of tape playback, press Z to eject the tape. Press (MODE) repeatedly to select the band. Press the number button ((1) to (6)) on which the desired station is stored. "MONO" indicator is displayed. The sound improves, but becomes monaural ("ST" disappears). To return to normal mode, select "MONOOFF. " 2 3 9 Other Functions Adjusting the sound characteristics You can adjust the bass, treble, balance, and fader. You can store the bass and treble levels independently for each source. Changing the sound and display settings The following items can be set: ·A. SCRL (Auto Scroll)* (page 12). ·M. DSPL (Motion Display) ­ the demonstration mode which appears when the tape is ejected and no source is selected (e. g. , tuner is turned off). ·BEEP ­ to turn the beep sound on or off. 1 2 Press (SEL). Press the preset number button to select the desired item. 1 Select the item you want to adjust by pressing (SEL) repeatedly. (See "Adjusting the sound characteristics" on page 10. ) 11 With Optional Equipment CD/MD Unit This unit can control external CD/MD units. If you connect an optional CD unit with the CD TEXT function, the CD TEXT information will appear in the display when you play a CD TEXT disc. Automatically scrolling a disc name -- Auto Scroll If the disc name, artist name, or track name on a CD TEXT disc or MD exceeds 8 characters and the Auto Scroll function is on, information automatically scrolls across the display as follows: · The disc name appears when the disc has changed (if the disc name is selected). · The track name appears when the track has changed (if the track name is selected). Playing a CD or MD 1 Press (SOURCE) repeatedly to select CD or MD. [. . . ] Cause/Solution ·Cancel the ATT function (page 10). ·Set the fader control to the centre position for two-speaker systems. · The power cord or battery has been disconnected. Remove the front panel and clean the connectors. [. . . ]