User manual SONY XR-TC80

[. . . ] CD Stereo System XR-TC80 U C OPERATING INSTRUCTIONS En (English) MANUAL DE INSTRUCCIONES E (Español) MODE D'EMPLOI Owner's record For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty. (Lot No. ) F (Français) For assistance and information (United States and Puerto Rico) 8C-DC1-903-01 020610AMI-H-BF WARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. IMPORTANT SAFETY INSTRUCTIONS Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. [. . . ] - To select the 11th track, press +10 and 1. To change the display in playback mode Press DISPLAY during play. The display changes in the following order: Track number being played and elapsed playing time Remaining time of play ·Remaining time of play cannot be displayed during " 1, random or programmed play. To remove the disc Press zOPEN/CLOSE to open the CD window, hold the disc in hand and press PUSH on the pivot so that the disc is released. En DISC DIRECT PLAY 1-3 zOPEN/CLOSE CDE CDE s DISC DIRECT PLAY 1-3 f, g This unit plays back finalized CD-R/RW discs as well as audio CDs. 2 To play two or three discs, press the desired DISC DIRECT PLAY 1-3 / DISC CHANGE to rotate the tray and load a disc in the same way as step 1. The selected tray number appears in the display. Playing CDs 1 Press zOPEN/CLOSE to open the CD window and load disc(s). Fit the disc center hole to the pivot of the tray with the label side facing you and press down the part around the hole until the disc is securely locked. 3 Press zOPEN/CLOSE to close the CD window. Total track number and total playing time of the currently selected disc will be displayed after the unit reads it. 4 To play all the discs (all disc play), press CDE. To play one desired disc (single disc play), press DISC DIRECT PLAY 1-3. Playing disc number appears in the display. To switch between all disc play and single disc play during play Press one flashing button (a currently playing disc number button) of DISC DIRECT PLAY 1-3 during play. ·In single disc play, only one button of DISC DIRECT PLAY 1-3 lights up and flashes. 8 Random/Repeat play In random play mode the unit plays all the tracks in random order. In repeat play mode it repeatedly plays all the discs or the track being played. You can select random and repeat all play at the same time. 1 Press RANDOM/REPEAT repeatedly on the remote control. The mode changes as follows: "" 1": Plays one track repeatedly. """: Plays all the tracks repeatedly. "RANDOM": Plays all the tracks randomly. "RANDOM " ": Plays all the tracks repeatedly in random order. Programmed play Up to 30 tracks can be programmed from any of the loaded discs. 1 Press PROGRAM on the remote control in stop mode. "PRGM" flashes on the display. To check the program Press f or g repeatedly in stop mode. The track number and program number are displayed in succession. To clear the program Press s in stop mode. "PRGM" disappears from the display. To add tracks to the program Repeat steps 2 and 3 before starting playback. The tracks are added to the end of the program. To change the programmed tracks Clear the program and repeat all the steps again. Notes on CDs 2 Press one of DISC DIRECT PLAY 1-3 to select a disc. Wait for a while until the disc tray is selected. En 3 Press the numbered buttons on the remote control to program a track. -To select the 25th track, press +10, +10 and 5. -To select the 11th track, press +10 and 1. The selected track number lights up on the display. 2 To play all discs: press CDE. To play a single disc: press the desired DISC DIRECT PLAY 1-3. To cancel random/repeat play Press RANDOM/REPEAT on the remote control repeatedly until "RANDOM" or """ disappears. Direct selection of the tracks with the numbered buttons (Direct play) cancels random play mode. [. . . ] Resetting the unit If an unusual condition occurs in the display window, reset the unit as follows: 1 Press POWER to turn off the power. If the power cannot be turned off, disconnect the AC power cord, then plug it in again. 2 Hold down s and press POWER on the main unit. Everything stored in memory after purchase is cleared. En Troubleshooting If your unit fails to perform properly, check the following guide and the relevant sections of the Operating Instructions. There is no sound ·Are the speakers and AC power cord connected properly? [. . . ]