User manual SONY XR-U220

[. . . ] · When no car circuits are rated high enough, connect the unit directly to the battery. Connection example (2) Notes (2-A) · Be sure to connect the earth cord before connecting the amplifier. · If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Tip (2-B- ) For connecting two or more CD/MD changers, the source selector XA-C30 (optional) is necessary. 4 5 6 7 Connection diagram (3) 1 To a metal surface of the car 2 First connect the black earth lead, then connect the yellow and red power input leads. To the power aerial control lead or power supply lead of aerial booster amplifier Notes · It is not necessary to connect this lead if there is no power aerial or aerial booster, or with a manually-operated telescopic aerial. [. . . ] · When your car has a built-in FM/AM aerial in the rear/side glass, see "Notes on the control and power supply leads. " To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. To the +12 V power terminal which is energized in the accessory position of the ignition key switch Notes · If there is no accessory position, connect to the +12 V power (battery) terminal which is energised at all times. Be sure to connect the black earth lead to it first. · When your car has a built-in FM/AM aerial in the rear/side glass, see "Notes on the control and power supply leads. " To the +12 V power terminal which is energised at all times Be sure to connect the black earth to it first. ×4 ×2 Parts Iist (1) Equipment used in illustrations (not supplied) , ( ) The numbers in the list are keyed to those in the instructions. 3 Caution Handle the bracket 1 carefully to avoid injuring your fingers. 4 Front speaker Power amplifier Rear speaker CD/MD changer CD/MD 1 5 3 Supplied with the CD/MD changer CD/MD Source selector XA-C30 Supplied with XA-C30 XA-C30 BUS AUDIO IN BUS CONTROL IN from car antenna BUS AUDIO IN AUDIO OUT XR-U220 Fuse (10 A) (10 ) RCA pin cord (not supplied) RCA ( ) AUDIO OUT REAR Blue/white striped C ep-e ca 7 AMP REM 3 Max. 0, 3 White White/black striped C ep-e ca Gray Gray/black striped C cep-ep ca Green Left Green/black striped C ep-ee ca Purple e Purple/black striped C ep-e ca Yellow Red Black Left 1 Blue Right ANT REM Max. 0, 1 2 4 Right 5 Notes on the control and power supply leads · The power aerial control lead (blue) supplies +12 V DC when you turn on the tuner. · When your car has built-in FM/AM aerial in the rear/side glass, connect the power aerial control lead (blue) or the accessory power input lead (red) to the power terminal of the existing aerial booster. · A power aerial without relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition key is turned off. pae "pea ce p a ypae". ·p e a ycpca ece c py cepeea ae aee c a ype a a pea cyape aee c a, yaae a pexpaex cex e. ·Ec ae aee c a ype a a e ca ce, cee ycpc apy ayypy. 3 xy AMP REMOTE IN e yce c apa e cyec ycee. ee py cce e pec pee ycpca. (1) , . 4 y a +12 B, apee a p aec, a aa ycae ee a ex ycpc · Ec e e e aapayp, e ee a (ayypa) +12 B, a py ae aec c. · Ec a ae/ cee a ycaea cpea aea aa FM/AM, c. pae "pea ce p a ypae". Bae 1 , . 5 ee a +12 B, a py ae aec c Caaa e ep p aee. 1 4A (OFF) B (RELEASE) 51 182 mm 53 m m 2 3 4 4 Dashboard 1 Fire wall 6 2 1 Bend these claws outward for a tight fit, if necessary. . 5 5 54 4 3 6A max. paep 5× 8 TOYOTA 4 to dashboard/center console pp ae/epa c B NISSAN max. paep 5× 8 4 to dashboard/center console pp ae/epa c Bracket pe 4 max. paep 5× 8 Bracket pe 4 max. paep 5× 8 Bracket pe Bracket pe Existing parts supplied with your car ea, xe e a Existing parts supplied with your car ea, xe e a Precautions ·Choose the installation location carefully so that the unit will not interfere with normal driving operations. [. . . ] paep 5× 8 Bracket pe 4 max. paep 5× 8 Bracket pe Bracket pe Existing parts supplied with your car ea, xe e a Existing parts supplied with your car ea, xe e a Precautions ·Choose the installation location carefully so that the unit will not interfere with normal driving operations. ·Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as in direct sunlight or near heater ducts. ·Use only the supplied mounting hardware for a safe and secure installation. Warning when installing in a car without ACC (accessory) position on the ignition key switch Be sure to press (OFF) on the unit for two seconds to turn off the clock display after turning off the engine. When you press (OFF) only momentarily, the clock display does not turn off and this causes battery wear. · , . [. . . ]