User manual SONY XS-AW850

[. . . ] * The torque value should be less than 1 N·m. REMO TE +12V GND µ REMO Pass the leads through the cap, connect the leads, then cover the terminals with the cap. +12V GND * The unit turns the power on or off automatically depending whether the power of the car audio is turned on or off when an ACC power supply cord of the car audio is connected to the unit. Line Input Connection Owner's Record Car audio * The unit does not turn on or off together with the car audio when an ACC power supply cord of the car audio is connected to the unit. Be sure to connect the remote control lead of the car audio to the remote terminal. The model and serial numbers are located on the bottom of the unit. [. . . ] 4 LEVEL control Turn this control to adjust the subwoofer output level. 5 POWER/PROTECTOR indicator Lights up in green while the unit is in operation. The color will change from green to amber and the unit will shut down when the protection circuit is activated if a DC current is generated. Installation Parts list Dimensions 1 2 3 HI - PASS FILTER FRONT 50Hz 100Hz Precautions 180 (7 1/8) 50Hz 100Hz SUB WOOFER F+R MODE F + ­ PHASE ×4 ø5 × 25 ×4 ø5 × 20 ×4 LEVEL MIN MAX Unit: mm (in. ) Before installation ·Choose the installation location carefully so that the unit does not interfere with driving and/or visibility. ·Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or heater exhaust, or where it would be subject to dust, dirt, or excessive vibration. ·This unit may cause interference in the car audio or other A/V devices. If this occurs, relocate the unit at least 50 cm from the affected device. 226 (9) ·Use only the supplied mounting hardware for a safe and secure installation. ·Consult your nearest Sony dealer for the location of an authorized installer if you require assistance. Note on mounting board (not supplied) It is recommended that a mounting board be used for safe installation. The board should be thicker than 18 mm (3/4 in. ) to accept the supplied mounting screws. INPUT HIGH LEVEL INPUT 190 (7 1/2) REAR SPEAKER OUT ACC POWER/ PROTECTOR 30A REMOTE +12V GND 335 (13 1/4) 380 (15) 1 Fasten the fittings 1 securely to the unit with the screws 2. Specifications 2 1 AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 22 watts per channel minimum continuous average power into 4 ohms, both channels driven from 100 Hz to 20 kHz with no more than 1% total harmonic distortion. Other Specifications Speaker section Woofer Impedance 20 cm, cone type 6 ohm Harmonic distortion Front/Rear 0. 1 % or less (at 1 kHz) Subwoofer 0. 05 % or less (at 100 Hz) Input sensitivity 0. 7 V (RCA pin jacks) 8. 0 V (High level input) High-pass filter 50 ­ 150 Hz, ­12 dB/oct System Section Power requirements 12 V DC car battery (negative ground) Power supply voltage 10. 5 ­ 16 V Current drain at rated output: 19 A Remote input: 1. 5 mA Dimensions Approx. 380 × 226 × 190 mm (w/h/d) (15 × 9 × 7 1/2 in. ) not incl. projecting parts and controls Mass Approx. accessories Supplied accessories Mounting screws (ø5 × 20: 4, ø5 × 25: 4), Fittings (4), Terminal Cap Optional accessories Connecting cord for power amplifier RC-46 Design and specifications are subject to change without notice. ·This unit is designed for negative ground 12 V DC operation only. ·Use speakers with an impedance of 4 ohms. ·Do not connect any active speakers (with built-in amplifiers) to the speaker terminals of the unit. Doing so may damage the active speakers. ·Avoid installing the unit in areas subject to: -- high temperatures such as from direct sunlight or hot air from the heater -- rain or moisture -- dust or dirt. ·If your car is parked in direct sunlight and there is a considerable rise in temperature inside the car, allow the unit to cool down before use. ·Be sure to install the unit horizontally so that the air duct of the cooling fan or its fin will not be covered with carpet etc. ·If this unit is placed too close to the car radio or antenna, interference may occur. [. . . ] n Be sure to connect the remote control lead of the car audio to the remote terminal. · The POWER/PROTECTOR indicator flashes. Alternator noise is heard. Use speakers with suitable impedance (4 ). The speaker outputs are short-circuited. [. . . ]