User manual SONY XS-W6921

[. . . ] 1 160 g por altavoz × Peak power Rated power Impedance Sensitivity Frequency response Mass Puissance de crête Puissance nominale Impédance Sensibilité Réponse de fréquence Poids XS-W1621 Coaxial de 2 vías: Graves 16 cm, tipo cónico Agudos 4, 5 cm, tipo cónico Corriente máxima 180 W Corriente nominal 50 W Impedancia 4 Sensibilidad 91 dB/W/m Respuesta en frecuencia 30 ­ 25 000 Hz Peso Aprox. 700 g por altavoz Altavoz XS-W1621 Speaker Coaxial 2-way: Woofer 16 cm (6 3/8 in. ) cone type Tweeter 4. 5 cm (1 13/16 in. ) cone type 180 watts 50 watts 4 ohms 91 dB/W/m 30 ­ 25, 000 Hz Approx. [. . . ] ·A hole for mounting may already be cut out of the inner panel of the door (front or rear) or the rear tray. In this case, you need to modify the board only. · If you are to mount this speaker system in the door (front or rear), make sure that the speaker terminals, frame or magnet do not interfere with any inner parts, such as the window mechanism in the door (when you open or close the window), etc. Also make sure that the speaker grille does not touch any inner fittings, such as the window cranks, door handles, arm rests, door pockets, lamps or seats etc. ·If you are to mount this speaker system in the rear tray, make sure that the speaker terminals, frame or magnet do not touch any inner parts of the car, such as the torsion bar springs (when you open or close the trunk lid), etc. Also make sure that the speaker grille does not touch any inner fittings, such as seat belts, head rests, center brake lights, inner covers of the rear wipers, curtains or air purifiers etc. * (XS-W1621) **(XS-W1321) Mounting from the car interior (Top mounting)/Montage depuis l'intérieur de l'habitacle (Montage par le haut) Montaje desde el interior del automóvil (montaje superior)/ DOOR (FRONT/REAR)/PORTIÈRE (AVANT/ARRIÈRE)/ PUERTA (FRONTAL/POSTERIOR)/ (XS-W1621, XS-W1321) REAR TRAY/PLAGE DE CUSTODE/BANDEJA POSTERIOR/ (XS-W6921) 1 Mark the four bolt holes and make them 3. 3 mm* (5/32 in. ) in diameter. Marquer les quatre orifices des boulons et percer des trous de 3, 3 mm* (5/32 po) de diamètre. Marque los orificios para los cuatro pernos y haga agujeros de 3, 3 mm* de diámetro. * * When using 5: ø 5 mm ( /32 in. ) * Si vous utilisez 5: ø 5 mm (7/32 po) * Si utiliza 5 = ø 5 mm * 5 ø 7 1 Mark the four bolt holes and make them 3. 3 mm (5/32 in. ) in diameter. Marquer les quatre orifices des boulons et percer des trous de 3, 3 mm (5/32 po) de diamètre. Marque los orificios para los cuatro pernos y haga agujeros de 3, 3 mm de diámetro. 1 ø 3. 3 (5/32 ) 1 217 (8 5/8 ) Avant le montage Une profondeur d'au moins 73 mm / 2 /8 po (45 mm / 1 13/16 po)* (46 mm / 1 13/16 po)** est nécessaire pour effectuer le montage encastré. Mesurez la profondeur de l'emplacement où vous souhaitez monter le haut-parleur et assurez-vous que ce dernier ne gêne en rien les autres composants du véhicule. [. . . ] Vers le cordon du haut-parleur d'une voiture. Al cable del altavoz del auto. 3 To speaker cord of a car. [. . . ]