User manual SONY XVM-B62

[. . . ] 2-666-477-11 (1) Mobile Monitor Operating Instructions Mode d'emploi US FR Owner's Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. XVM-B62 Serial No. XVM-B62 2006 Sony Corporation Warning For the customers in the United States This product contains mercury. [. . . ] The "Picture" screen appears. Picture 32 Press+/-, or MENU. The setting value of the item selected appears in this area. Each time you press (MENU), the setting screen changes in the following sequence: Picture t Brightness t Color t Hue* t Video Adjust t Mode t Blue Back t Select NTSC or PAL System t Menu Off * Appears only when the NTSC color system is selected. 2 Press or to adjust to the desired setting. See the following for the setting options. 7 Connections Installation diagram Refer to the installation diagram and ask a qualified technician for the installation of the unit. Front Left speaker Tweeter Left Head unit Tweeter Right Mobile Monitor Front Right speaker Rear Left speaker Subwoofer Rear Right speaker Be sure to securely fasten all equipment to the car chassis, etc. , to prevent them moving while your car is in motion. Notes · All equipment other than one Mobile Monitor is optional. · To attach the monitor using the supplied collar, consult the store you purchased this unit or your nearest Sony dealer. 8 Connection diagram Refer to the connection diagram for the proper connections. Mobile monitor XVM-B62 (6. 2-inch wide color LCD Monitor) Video in cable (3 m) To the parking brake switch cord (see page 10) (To a metal surface of the car chassis when you attach the monitor to the headrest) Black To a metal surface of the car chassis Black To the +12 V power terminal which is energized in the accessory position of the ignition key switch Light green Red Fuse (10 A) L/C filter VIDEO 1 IN DVD player, video CD player, etc. VIDEO 2 IN 9 When installing the monitor on the dashboard Be sure to connect the parking cord (Light green) to the parking brake switch cord. The mounting position of the parking brake switch cord depends on your car. Consult your car dealer or your nearest Sony dealer for further details. Foot brake type Additional Information Attaching and detaching the monitor Detaching the monitor from the collar Note Be careful not to pull out the cable too much when detaching the monitor from the collar. Parking brake switch cord Hand brake type Insert a plastic card (not supplied) between the collar and the top of the monitor. The catches are released, and you can detach the monitor from the collar. Plastic card (not supplied) Parking brake switch cord collar Using the tap Attach the supplied tap to the end of the parking cord (Light green) and the parking brake switch cord. Parking brake switch cord Tap (supplied) Attaching the monitor to the collar Set the monitor to the collar securely until you hear click sound. x Parking cord (Light green) Note If the parking brake switch cord is too thin, connect the parking cord (Light green) to the parking brake switch cord directly without using the tap. 10 Maintenance Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Fuse Some stationary green, blue or red dots may appear on the monitor. These are called bright spots, and can happen with any LCD. The LCD panel is highly sophisticated, and more than 99. 99 % of the segments used in the panel are flawless. However, there is a possibility that less than 0. 01 % of the segments are defective and may not light up properly. Fuse Warning Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit. About the liquid crystal display (LCD) panel Do not press on the LCD panel on the unit as doing so can distort the picture or cause a malfunction. The picture may become unclear, or the LCD panel may be damaged. Notes on cleaning -- Clean the LCD panel with a slightly damp soft cloth. -- Do not use solvents such as benzine, thinner, commercially available cleaners or antistatic spray. · Do not use the unit in temperatures under 0 °C (32 °F) or over 45 °C (113 °F). · If your car was parked in a cold or hot place, the picture may not be clear. The picture will become clear after the temperature in your car becomes normal. 11 Specifications Monitor Liquid crystal color display TFT-LCD active matrix system Picture size 6. 2 inches wide screen (16:9) 137. 5 × 77. 2 mm (5 1/2 × 3 1/8 in) (w × h) Picture segment 336, 960 (w 1440 × h 234) dots Power requirements 12 V DC car battery (negative ground) Current drain Approx. 550 mA Dimensions 164. 2 × 106. 6 × 29 mm (6 1/2 × 4 1/4 × 1 1/16 in) (w/h/d) Operating temperature 0 °C ­ 45 °C (32 °F ­ 113 °F) Mass Approx. 450 g (1 lb) System Drive system Troubleshooting The following checklist will help you solve problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General No picture ·The power cord or battery has been disconnected. [. . . ] La position de montage du cordon du capteur du frein à main varie selon la voiture. Consultez votre concessionnaire automobile ou votre revendeur Sony le plus proche pour obtenir plus de détails. Type pédale de frein Informations complémentaires Installation et retrait du moniteur Pour retirer le moniteur du collier Remarque Prenez garde de ne pas tirer excessivement le câble lorsque vous retirez le moniteur du collier. Cordon du capteur du frein à main Type frein à main Insérez une carte en plastique (non fourni) entre le collier et le haut du moniteur. Les pattes sont déverrouillées et vous pouvez alors retirer le moniteur du collier. Carte en plastique (non fourni) Collier Cordon du capteur du frein à main Utilisation de la dérivation Raccordez la dérivation fournie à l'extrémité du cordon du frein (vert clair) et au cordon du capteur du frein à main. Dérivation (fournie) Cordon du capteur du frein à main Pour installer le moniteur sur le collier Placez correctement le moniteur sur le collier jusqu'à ce que vous entendiez un déclic. x Cordon du frein à main (vert clair) Remarque Si le cordon du capteur du frein à main est trop fin, raccordez le cordon du frein (vert clair) au cordon du capteur du frein à main directement sans utiliser la dérivation. 10 Entretien Remplacement du fusible Lorsque vous remplacez le fusible, veillez à utiliser un fusible dont l'ampérage correspond à celle indiquée sur le fusible d'origine. Si le fusible fond, vérifiez le branchement de l'alimentation et remplacez le fusible. [. . . ]