User manual SONY ZS-M7

[. . . ] 3-861-445-11(1) Personal MiniDisc System Operating Instructions ZS-M7 ©1998 by Sony Corporation Warning To prevent fire or shock hazard, do not expose the player to rain or moisture. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. [. . . ] If both of the combined tracks had track names, the name of the latter track is erased. The total number of tracks in the music calendar decreases by one. Editing recorded tracks on the MD 37 Editing recorded tracks on the MD Moving recorded tracks (Move Function) You can change the order of the tracks. After you move the track, the track numbers are renumbered automatically. Jog dial EDIT ENTER·YES Note After you stop recording, do not disconnect the AC power cord or move the player while "TOC EDIT" is flashing in the display. If you do so, recording may not be done properly. Example: Moving C to the position of track 1 Track number Moving Track number of the C changes to 1 1 C 2 A 3 B 4 D 1 A 2 B 3 C 4 D 1 2 3 4 Play the track you want to move. Press EDIT repeatedly until "Track Move" appears in the display. "nTrack 003?" appears in the display, and onetrack repeat play starts. Turn the jog dial to select the new track position. If you want to cancel the move function at this point: Press CANCEL·NO or MD p. 5 Press ENTER·YES. "Complete" appears in the display for a few seconds after the track is moved. 38 Editing recorded tracks on the MD Labeling recordings (Name Function) You can label the MDs and the tracks you have recorded with letters, numbers and symbols. Each label can be made up of up to 100 characters. You can input up to about 1, 700 characters into each MD. CANCEL·NO Jog dial ¿ ENTER·YES EDIT ÷ Editing recorded tracks on the MD Labeling an MD 1 2 3 4 Insert the MD you want to label, and stop the MD play. Press EDIT repeatedly until "Disc Name" appears in the display. If the disc name has been already labeled, the disc name appears in the display. Press DISPLAY repeatedly to select the type of characters. Each time you press DISPLAY, the character changes as follows: Uppercase letters n Lowercase letters n Numbers and symbols. You can use the following characters: The type of characters Uppercase letters Lowercase letters Numbers and symbols Characters (symbols) ABCD. . . . . WXYZ', /: (space) abcd. . . . . wxyz', /: (space) 0123456789!"#$%&()*. ;<=>?@_`+ ­', /: (space) continued Editing recorded tracks on the MD 39 Labeling recordings (Name function) (continued) 5 6 Turn the jog dial counterclockwise or clockwise to select the characters. The cursor shifts rightward and waits for the input of the next character. Cursor Display 7 Note After you stop recording, do not disconnect the AC power cord or move the player while "TOC EDIT" is flashing in the display. If you do so, recording may not be done properly. Repeat steps 4 through 6 to complete the entire name. The name has been labeled on the MD. 8 Labeling a track 1 2 3 Play the track you want to label. Press EDIT repeatedly until "Track Name" appears in the display. If the track name has been already labeled, the track name appears in the display. 4 Input the characters according to steps 4 through 8 of "Labeling an MD. " The name has been labeled on the track. 40 Editing recorded tracks on the MD To change the characters · To add characters after the existing characters 1 Move the cursor to the right of the last character using ÷. [. . . ] · Make sure that you are pointing the remote at the remote sensor on the player. · Remove any obstacles in the path of the remote and the player. · Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. · Move closer to the player when using the remote. Operation may become unstable depending on the power supply or other causes because this player employs a microcomputer to link each operation. [. . . ]