User manual SOUNDCRAFT DELTA SR

[. . . ] The Mixtreme card is available with an S/PDIF option. If your Mixtreme card has the S/PDIF option installed, coaxial digital S/PDIF cables should also be connected from the Mixtreme S/PDIF output to the 328 S/PDIF input and vice versa. Audio Connections Connections 328 TDIF 1 328 TDIF 2 Mixtreme TDIF 1 Mixtreme TDIF 2 Mixtreme S/PDIF Out 328 S/PDIF Out 328 S/PDIF In Mixtreme S/PDIF In The TDIF connections allow digital transfer of either direct outputs for input channels 1-16 to the Mixtreme card, or the Digital 328's 8 Group outputs. [. . . ] If your Mixtreme card has the S/PDIF option installed, coaxial digital S/PDIF cables should also be connected from the Mixtreme S/PDIF output to the 328 S/PDIF input and vice versa. Audio Connections Connections 328 TDIF 1 328 TDIF 2 Mixtreme TDIF 1 Mixtreme TDIF 2 Mixtreme S/PDIF Out 328 S/PDIF Out 328 S/PDIF In Mixtreme S/PDIF In The TDIF connections allow digital transfer of either direct outputs for input channels 1-16 to the Mixtreme card, or the Digital 328's 8 Group outputs. The S/PDIF output from the console can be assigned to either the Mix output or 1 of 3 stereo auxilliary outputs. The 328 S/PDIF Input can be configured to be a digital Stereo Input or as a digital 2 Track Return. Spirit Digital 328 v2 2 Digital 328 Setup Wordclock To configure the Digital 328 as the wordclock master, enter the 328 menu pages by pressing the <MENU> button on the right hand side of the LCD display. Using the encoder beneath the display, scroll up or down until the 'Clock Source Sel' menu is highlighted, and press <ENTER>. Here, either the internal 44. 1kHz clock or the internal 48kHz clock must be selected, depending on the sampling rate at which you wish to work. Press <ENTER> to set the sample rate and <MENU> to return to the menu pages. 2 <Wordclock Src. > Internal:44. 1kHz or <Wordclock Src. > Internal:48. 0kHz Tape Ports To ensure that the Digital 328 Tape Ports are both set to TDIF to work with the Mixtreme, enter the 328 Menu pages by pressing the <MENU> button on the right hand side of the LCD display. Commonly the Mixtreme S/PDIF output would best be routed to Stereo Input 2, or the 2 Track Tape Return input. NOTE Assigning a digital source to an input will override an analogue signal, if present. Spirit Digital 328 v2 4 Press <MENU> to enter the menu pages, scroll through the pages until the `SPDIF I/P Setup' is highlighted and press <ENTER>. Using the encoder, select the destination for the S/PDIF input, press <ENTER> to set and <MENU> to return to the menu pages. If the S/PDIF input is not required, NOWHERE should be selected in the menu. NOTE < SPDIF Input > Route To: STE-1 < SPDIF Input > Route To: FX-1 < SPDIF Input > Route To: 2TRK < SPDIF Input > Route To:NOWHERE Soundscape Mixtreme 1. 2 Setup Guide 5 2 Mixtreme Setup Wordclock The Mixtreme must be set up to receive the wordclock transmitted by the 328. Open the Mixtreme mixer from via the Mixtreme icon on the Windows Taskbar. Under the Settings menu, set the Master Clock to TDIF Master Clock A. To save these settings, click on the `Settings' menu and select `Save Settings'. Spirit Digital 328 v2 6 Mixtreme Mixer Setup The Mixtreme mixer software allows full customisation for the routing of the 16 inputs and outputs available on the Mixtreme card. A basic setup utilising all 16 inputs and outputs is shown below. [. . . ] Under the Settings menu, set the Master Clock to TDIF Master Clock A. To save these settings, click on the `Settings' menu and select `Save Settings'. Spirit Digital 328 v2 6 Mixtreme Mixer Setup The Mixtreme mixer software allows full customisation for the routing of the 16 inputs and outputs available on the Mixtreme card. A basic setup utilising all 16 inputs and outputs is shown below. [. . . ]