User manual SOYO SY-6KL QUICK START GUIDE

[. . . ] Our customers should ensure that their use of our products does not infringe upon any patents. to respect the valid patent rights of third parties and not to infringe upon or assist others to infringe upon such rights. Restricted Rights Legend: Use, duplication, or disclosure by the Government is subject to restrictions set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at 252. 277-7013. About This Guide: This Quick Start Guide is for assisting system manufacturers and end users in setting up and installing the mainboard. [. . . ] Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan, Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock Switch. ), Wake-On-LAN card, VGA card, Sound Card, and other devices. For more details on how to connect internal and external peripherals to your new SY-6KL Mainboard, please refer to SY-6KL Mainboard User's Guide and Technical Reference online manual on CD-ROM. Connectors and Plug-ins Connect the SB-Link TM (PC-PCI) cable from your PCI audio card to this header. CPU Cooling Fan: FAN 1 Connect the WOL cable from your LAN card to JP44. Chassis Fan: FAN 3 Connect the CPU cooling fan cable to the Connect the case cooling fan cable to the FAN1 power connector. USB TB LED SPK Plug your USB devices Connect your Turbo LED Connect the speaker cable to to this header. RESET IDE LED KB-LOCK Connect the Power LED and the KB Lock switch to this header. AT Power Supply Connect the AT Power Supply cable to this connector ATX Power Supply: ATX PW Attach the ATX Power cable to this connector. When using the PS/2 Keyboard Wake-Up function, please make sure the ATX power supply can take at least 720mA load on the 5V Standby lead (5VSB) to meet the standard ATX specifications. Connect the reset button Connect the IDE device to this header. IrDA (Infrared Device Header): IR1 Connect the cable from your IrDA device to this header. ATX Power On/Off: PWRBT Connect your power switch to this header (momentary switch type). Depending on the BIOS setting, turning off the system is done by "one touch" or by pressing the switch for >4s longer than 4s. ATX Power Select: JPW1 If you use a non-standard ATX power supply, open this jumper. 7 Hardware Installation PCI Audio Card Header: SB-Link TM (PC-PCI) Wake-On-LAN Header: JP44 SY-6KL Quick Start Guide Step 3. Configure Memory Your board comes with three DIMM sockets and two SIMM banks, providing support for up to 384MB of main memory using DIMM modules from 8MB to 128MB and SIMM modules from 8MB to 64MB with no restriction on memory configuration. Therefore, you can install memory modules in any combination. For 66MHz front side bus CPUs use 12ns or faster memory. Memory Configuration MEMORY CONFIGURATION RAM Type Single RAM Module Size (MB) SIMM Bank Bank 0 EDO 8/16/32/64 DIMM 1 EDO/SDRAM DIMM Banks DIMM 2 EDO/SDRAM DIMM 3 EDO/SDRAM 8/16/32/64/128 8/16/32/64/128 8/16/32/64/128 Hardware Installation Notice 1: You must always install two (2) SIMM modules to complete the SIMM bank. Notice 2: Do not install memory modules in SIMM and DIMM 3 at the same time. Step 4. Set the CPU Frequency You do not need to set any jumper for the CPU frequency. Instead, CPU setting are changed through the BIOS [CHIPSET FEATURES SETUP]. Please refer to Chapter 3 - Quick BIOS Setup for details on how to set the Pentium® II processor frequency. Step 5. Enable/Disable PS/2 Keyboard Wake-Up (JP12) You can choose to enable the Wake-Up by PS/2 Keyboard or Mouse function by shorting pin 1-2 on jumper JP12, otherwise, remove the jumper cap to open pin 1-2 and disable this function. Support Wake-Up by Keyboard JP12 Setting Enable Enable Wake-up by Keyboard or Mouse function (short pin 1-2) Disable* (*Default) Disable Wake-up by Keyboard or Mouse function (open pin 1-2) Important: When using the PS/2 Keyboard Wake-Up function, please make sure the ATX power supply can take at least 720mA load on the 5V Standby lead (5VSB) to meet the standard ATX specifications. 8 SY-6KL Quick Start Guide Step 6. [. . . ] The Start Up program will activate the default HTML browser installed on your system (for example, Internet Explorer or Netscape) to visualize the contents of the SOYO CD. The SOYO CD contains useful information about your mainboard and other SOYO products available in as many as eleven different languages. For your convenience, this information is available in HTML format, similar to the format widely used on the Internet. 13 The SOYO CD Note: Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver installation program. When the installation is complete, most drivers require to restart your system before they can become active. SY-6KL Quick Start Guide (SOYO CD HTML Database in English*) (* The list of menu options may vary between languages) Note: If no HTML browser is installed on your system, the Start Up program will prompt you on whether or not you would like to install the Internet Explorer* browser. [. . . ]