User manual SPECO DVR-16/IP

[. . . ] 16 CHANNEL NETWORK READY DVR DVR-16/IP User's Manual Precautions All the safety and operation instructions should be read before the DVR-16/IP is operated. All the safety and operation instructions should be retained for future reference. Comply with operating instruction and notice warning information. Do not use strong or abrasive detergents when cleaning the DVR-16/IP. [. . . ] After you are in the sub-menu, you can pan/ tilt the speed dome freely by pressing SET and the direction buttons simultaneously. 1 RS-485 ID Setup 2 Zoom 3 Brightness 4 Set Preset Point 5 Enter Speed Dome Menu 6 Exit XXX XXX RS-485 ID Setup If you want to control the DSCP Speed Dome through the front panel, you should firstly check and modify the RS-485 ID here. Zoom Press the Enter button to enter the Zoom mode. You can simply push the right direction button to zoom in (tele) and the left direction button to zoom out (wide). Press the ESC button to exit the Zoom mode. Brightness Use the right and left direction buttons to adjust the brightness of the selected dome camera. Set Preset Point This item allows you to set the preset points. Pan/ Tilt the dome camera to the wanted position and give the preset point a number, and then press the Enter button. Enter Speed Dome Menu Press Enter on this item to go to the OSD menu of installed Speed Dome. 16 ¡» PELCO Speed Dome DVR-16/IP is capable of connecting to PELCO Speed Dome; the related settings can be adjusted here in this sub-menu. You can pan/ tilt PELCO Speed Dome by pressing SET and the direction buttons simultaneously after you are entering this sub-menu. PELCO Speed Dome 1 Protocol Setup 2 ID Setup 3 Zoom 4 Focus 5 Bfightness 6 Set Preset Point 7 Goto Preset Point 8 Enter Speed Dome Menu 9 Exit D_Type 1 Protocol Setup There are two Protocol types to choose from: D_type and P_type. ID Setup Each PELCO dome camera should have a ID individually. Zoom Press the right direction to zoom in (tele) and the left direction button to zoom out (wide). Focus Press the right/ left direction to change focus back and forth between a near object and a far object. Brightness Use the right and left direction buttons to adjust to appropriate brightness. Press ESC to exit when you finish the setting. Set Preset Point This item allows you to set preset points through the front panel. Pan/ tilt the connected receiver to a proper position, and then press the number buttons to assign a number to the preset point. Goto Preset Point Press right/ left direction button to select the number of the wanted preset point; then press Enter to go to the selected preset point. Enter Speed Dome Menu Press Enter on this item to enter connected PELCO dome camera's OSD menu. The function only supports a dome camera with DSCP protocol. CHIPER CRT. V9KRP CHIPER CRT. V9KRP ¡» This sub-menu allows you to set the receiver. In the sub-menu, you can pan/ tile the receiver by pressing SET and direction buttons simultaneously. Item 1~4 (ID Setup, Zoom, Focus, Brightness) Please refer to the receiver user's manual for detailed information. 1 ID Setup 2 Zoom 3 Focus 4 Brightness 5 Set Preset Point 6 Goto Preset Point 7 Set Group Dwell 8 Go Preset Group 9 Stop Preset Group 10 Exit 1 1 Set Preset Point This item allows you to set preset points through the front panel. [. . . ] Message: HDD Detect Fail Symptom: The HDD is unusable. for a new one. 40 Appendix 2: Supported HDD The supported HDDs are listed as below: Brand Capacity Rotation Speed Maxtor 40GB 5400 RPM Maxtor 80GB 5400 RPM Maxtor 80GB 7200 RPM Maxtor 80GB 7200RPM Maxtor 120GB 7200RPM Maxtor 160GB 7200RPM Maxtor 200GB 7200RPM Maxtor 250GB 7200RPM Part Number 4D040k2 4D080H4 D740X-6L 6Y080P0 6Y120P0 6Y160P0 6Y200P0 7Y250P0 Notice: 1. We strongly suggest do NOT use Seagate products, because them might have overheated problems while the DVR-16/IP is operating. We had compared other brand HDDs with Maxtor HDDs, we recommend user to use Maxtor HDDs with 8MB cache buffer that would bring DVR the optimum stability. 41 Appendix 3: RS-485 Command Set The texts of Data 0, 1 is in ASCII code format (Normal Command) Command OP_code Data 0, 1 Note Channel select "01" ~ "0G" Channel 1~16 Right "MR" Detail setting must Screen mode select reference User's manual Left "ML" Sequence "S1" ~ "S3" Sequence 1~3 Up key "DU" Down key "DD" Left key "DL" Right key "DR" Zoom/Enter "DZ" Play key "KV" Freeze/Pause "KA" A0H Set "KS" ESC "KE" List "KL" Date/Time "SD" Title "ST" Menu "SP" Key Lock "SK" Lock/ Un_Locked Goto "SR" Fast Rewind "RW" x1, x2, x4, x8 Fast Forward "FF" x1, x2, x4, x8 Universal End "UE" Goto Time1 BDH Data1, Data0 Year & Month Goto Time2 BEH Data1, Data0 Day & Hour Goto Time3 BFH Data1, Data0 Minute & "G" PS: Goto Time1: Year=00~99 (it means 2000~2099); Month=01~12 Goto Time2: Day=01~31; Hour=00~23 Goto Time3: Minute=00~59; "G" ASCII=47H Example: If the Keyboard ID is 00H, the DVR-16/IP ID is E0H. [. . . ]