User manual SPECTRONIQ PD-DVR 100 QUICK START

[. . . ] Note: You should use the input on the front of the recorder for non-permanent connections, such as to a camcorder when transferring its recorded video to DVD. If you would like to use S-Video, which offers higher quality video than composite, connect an S-Video cable (not included) between the video source and the S-Video input in the input block selected in step 1 above. If you would like to use composite video, connect an RCA cable between the video source and the Video input in the input block selected in step 1 above. [. . . ] If you would also like to connect the audio output to the display, connect the FR (right) and FL (left) outputs in the AUDIO OUT block on the rear of the recorder to the display's audio input. EZPDDVR100. indd 1 Vertical fold 8/26/2005 10:15:11 AM ENTER CHANNEL DISPLAY TITLE MENU RETURN Vertical fold SEARCH ADD/CLEAR PROGRAM STOP PAUSE/STEP PLAY ENTER VOLUME (LEVEL) Installing Batteries in the Remote Control 1. Remove the battery compartment cover from the rear of the remote and insert two AAA batteries (included). Replace the cover. Configuring the Display Set the clock: MUTE PREV NEXT DISPLAY TITLE MENU RETURN STOP REV FWD PAUSE/STEP PLAY SLOW REC 1. Press to enter the Setup menu. ZOOM A-B MODE INPUT Configure audio/video settings: 1. If you are connecting to a display using component video, press PREV NEXT REV FWD VOLUME (LEVEL) P-SCAN ANGLE REPEAT AUDIO SUBTITLE TIMER to select progressive scan or interlaced video. SLOW REC MUTE ZOOM A-B MODE SETUP DISC EDIT EDIT P-SCAN REPEAT TIMER SETUP DISC EDIT EDIT 2. Use to select the Clock sub-menu and press CHANNEL SEARCH ADD/CLEAR PROGRAM . Note: If you intend to use progressive scan video, ensure your display supports it. to select the Playback sub-menu and press . ENTER DISPLAY TITLE MENU RETURN 3. Use STOP PAUSE/STEP PLAY SYSTEM SETUP - CLOCK VOLUME (LEVEL) SYSTEM SETUP - PLAYBACK NEXT FWD PREV Date (mm/dd/yy) MUTE ZOOM REV 1 2/0 1/0 3 12:00:00 TV aspect ratio Rating level Digital audio output Analog audio output Speaker setting 16:9 OFF RAW 2 CH OK Time (hh:mm:ss) P-SCAN SLOW REC A-B MODE REPEAT TIMER SETUP DISC EDIT EDIT 3. Use to select Date and press INPUT . 4. Use to select Analog Audio Output and press to select the audio output format you are using. . 4. Enter the current date using the keypad. ANGLE AUDIO SUBTITLE INPUT If you have connected stereo audio only, select 2 CH. Using the Recorder 1. On the remote, press (standby). INPUT ANGLE AUDIO SUBTITLE If you have connected 5. 1 channel audio, select 5. 1 CH. to turn the recorder on and off CHANNEL For more information, refer to the User's Manual. Alternatively, you can select each digit individually by pressing SEARCH ADD/CLEAR PROGRAM ANGLE AUDIO SUBTITLE , then adjust it by pressing ENTER CHANNEL CHANNEL SEARCH ADD/CLEAR PROGRAM . ENTER SEARCH ADD/CLEAR PROGRAM DISPLAY TITLE MENU RETURN RETURN DISPLAY TITLE MENU STOP PAUSE/STEP PLAY STOP INPUT PAUSE/STEP VOLUME (LEVEL) ENTER PLAY PREV NEXT REV FWD ANGLE SLOW MUTE ZOOM A-B MODE REC AUDIO SUBTITLE VOLUME (LEVEL) DISPLAY PREV TITLE MENU NEXT RETURN P-SCAN REPEAT TIMER SETUP DISC EDIT EDIT STOP PAUSE/STEP REV PLAY FWD 5. Press to open the disc receptacle on the front of the recorder. CHANNEL SEARCH ADD/CLEAR PROGRAM to set the date. VOLUME (LEVEL) PREV SLOW NEXT REC 6. Use to select Time and press MUTE ZOOM A-B REV MODE FWD . 7. [. . . ] If the source is set to "Tuner", use channel. SETUP DISC EDIT CHANNEL CHANNEL SEARCH SEARCH SEARCH EDIT to change the 3. Use and press to select Tuner Input Source and press . to select the type of television signal you are using . ADD/CLEAR PROGRAM CHANNEL ADD/CLEAR ADD/CLEAR PROGRAM PROGRAM ENTER 4. Press ENTER to begin recording. DISPLAY TITLE DISPLAY STOP DISPLAY STOP TITLE ENTER Note: If you are connecting directly to a cable television wall outlet, contact your cable company to find out which system is in use in your area. [. . . ]