User manual SPECTRONIQ PLTV-4250

[. . . ] OMPLTV4250. book Page i Thursday, February 16, 2006 10:22 AM PLTV-4250 42" Liquid Crystal Display User's Manual OMPLTV4250. book Page ii Thursday, February 16, 2006 10:22 AM Protron PLTV-4250 Liquid Crystal Display User's Manual. © 2006 Protron Digital Corporation. Under copyright law, this manual may not be reproduced in any form, in whole or in part, without the prior written consent of Protron Digital Corporation. Disclaimer Protron Digital Corporation has reviewed this manual and provides it only as a guide to operation. [. . . ] · S-POS--When PIP is set to Standard PIP mode, adjusts the position of the secondary PIP window · SWAP--Swaps the primary and secondary sources · FREEZE--Freezes the content of the main window 13 OMPLTV4250. book Page 14 Thursday, February 16, 2006 10:22 AM Using the Remote Control Button(s) Function Brings up the V-Chip configuration menu Sets the display sleep timer. The timer can be turned off or set to 30, 60, 90, or 120 minutes. Selects the signal source (the signal source for the main window when PIP is enabled): TV, AV1, AV2, AV3, S-Video, YPbPr1, YPbPr2, HDMI, DTV, or VGA Used to enter numbers on the display and to select the television channel Returns to the previous channel When viewing HDTV, used to jump to a television channel once it has been entered on the keypad Selects the aspect ratio used by the display: 4:3 or Full (16:9) FULL 4:3 Mutes the audio When viewing HDTV, brings up the HDTV program guide, which displays program schedules and information for each channel Turns surround sound simulation on and off Selects the television channel Adjusts the audio volume Brings up the On-Screen Display Selects the MTS (Multichannel Television Sound) audio channel used for television: Mono, Stereo, or SAP (Secondary Audio Programming) Displays current source and television channel information 14 OMPLTV4250. book Page 15 Thursday, February 16, 2006 10:22 AM Using the Remote Control Button(s) Function Cycles through the closed captioning modes: Off, C1­4, and T1­4 Used to navigate display menus Selects the highlighted item or confirms the current adjustment Note: To use a universal remote with your display, program the remote to control any NEC television. Replacing the Remote Batteries The remote requires two AAA batteries, which are held in a small enclosure on the rear of the remote. Release the tab and pull the enclosure out of the remote. Remove the old batteries and replace them with the new batteries. Ensure the batteries are oriented as indicated in the enclosure. Snap the enclosure back into the remote. 15 OMPLTV4250. book Page 16 Thursday, February 16, 2006 10:22 AM Configuring the Display The On-Screen Display (OSD) allows you to configure the operation of the LCD. You can change video and audio settings, activate and configure Picture-in-Picture (PIP) and closed captioning, select television channels, control access to mature programming, and configure other general display behavior. Press the MENU button on the remote or the top of the display. Once the OSD appears, use the at the top of the OSD. Use the and and buttons to navigate the menus represented by icons 3. Press the ENTER button to enter the selected menu. Press the ENTER button to select the desired item. If no text is displayed next to the item name, a sub-menu will appear upon pressing ENTER. Repeat steps 4 and 5 to navigate the sub-menu. If the selected item is an adjustable parameter, one of two things will happen: A pop-up box will appear, in which case use ENTER to accept the value. and to adjust the parameter and then press The parameter will edit in place, in which case use and to adjust the value and then press ENTER to accept. While editing the parameter, a check mark will show next to the currently selected value. Note: The currently selected source determines which menus are available in the OSD. The following table lists the menus available for each source: Menu Source TV AV1 AV2 AV3 S-Video YPbPr1 YPbPr2 HDMI DTV VGA Video · · · · · · · Audio · · · · · · · · · · Misc. · · · · · · · · · · · · · · TV · PC DTV 16 OMPLTV4250. book Page 17 Thursday, February 16, 2006 10:22 AM Configuring the Display Video The Video menu allows you to change the display's video settings. You can adjust the following parameters: Contrast Sets the variation between light and dark colors Brightness Sets the brightness of the display image Saturation Sets the saturation of color in the display image Hue Sets the intensity of color in the display image Sharpness Sets the image sharpness Phase (YPbPr1 and YPbPr2 only) Adjusts the phase of the video synchronization Flesh Tone Turns on and off image filtering to improve flesh tones in the image Color Temperature Sets the color temperature used by the display: Cool, Normal, Warm, or a user-defined setting. [. . . ] If the issue cannot be resolved over the phone with trouble-shooting techniques, you may be eligible for warranty service. To request warranty repair, you may also contact us by e-mail at protron@ewestcsp. com. All warranties must be authorized by Protron prior to service and will result in the issuance of an authorization number for service. · For televisions with screen sizes of 37" or less, you will be requested to ship your television to our National Return Center. [. . . ]