User manual SPL VOLUME2

[. . . ] 6 Power Supply, ON/Off Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Rear Panel Graphic, Signal Connections, XLR Pin Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It should also be kept away from transformers, motors, power amplifiers and digital processors. You may risk electric shock and damage to your equipment. · Leave repairs and maintenance to a qualified service technician. Should foreign objects fall inside the case, contact your authorized dealer or support person. · To avoid electric shock or fire hazards, do not expose your unit to rain or moisture. · If the danger of lightning is foreseeable, unplug the unit. Never touch a power cable during a thunderstorm--danger of life!· Always unplug the cable by pulling on the plug only; never pull on the cable. · Use a soft, lint-free cloth to clean the case. Avoid cleaning agents as they may damage the unit. if necessary, use an acid-free cleaning oil instead. The power supply was carefully engineered to provide clean and consistent current ­ an important prerequisite for excellent audio. Built around a toroidal transformer, the power supply generates a minimal electromagnetic field with no hum or mechanical noise. The output side is filtered by an RC circuit to extract noise and hums inherent in commercial AC power. All audio-related components are fed by two separate voltage regulators to minimize disturbance from other components. An AC power cord is included for connection to the standard 3-prong IEC connector. The transformer, power cord and IEC connector are VDE, UL and CSA approved. The AC fuse is rated at 250 mA (230 V version) or 500 mA (115 V version). Power Supply Volume 2 5 Rear Panel Power Supply, On/Off Switching Be sure before connecting the Volume 2 to power that the rear-chassis voltage supply is switched to the proper local rating (either 230 or 115 volts). Above all, before connecting any machines, always take additional care to power down all those to be used (and move the rear-chassis power supply switch of the Volume 2 to the "down" position). Finally, always use the following procedure in powering up your assembly: Always power on your Volume 2 first before the power amp or active speakers. When powering down, always power off the power amp or active speakers before your Volume 2. Not following this sequence can result in ear or speaker damage from high level discharges! [. . . ] On the other hand, the power amp's/active speaker's input sensitivity should be raised if the 83 dB SPL point is reached far before the 60% control level. In cases where regulating power amp/active speaker inputs is not enough, one may reach good values by changing the D/A converter output level (for example from +4 dB to 0 or -10 dB in cases where this switch option may exist). In any case, the converters should always be driven at full scale from the DAW. Mute You guessed it . . . It is particularly valuable in panic situations, for example, if the computer crashes and its converters suddenly output uncontrolled high level noise. [. . . ]